IchGucksLive are you good with spindle orient? are you still fighting thatstill yup http://tom-itx.no-ip.biz:81/~webpage/cnc/configs/screenshots/M19_R10_P1.png all that and it's still not turning peepsalot: keep save in Austin Texas Harvey is hidding your way tom orient from 2.8 i don't have 2.8 2.7.11 ever since 3D printing took over manufacturing and replaced CNC the channel became quiet :) i'd rather hang out here than in #reprap thankyou Tom_L: as i see the orent error is there but this shout trigger the spindle motion people new to CNC also seem to want to suffer with GRBL and a *duino before they find out what they really need * TurBoss has quit IRC (Ping timeout: 248 seconds) IchGucksLive the hal is in that dir too let me read Tom_L: orient mode =1 and you got a Negativ goto bad idee i tried 0 too does the spindle make M4 yes http://tom-itx.no-ip.biz:81/~webpage/cnc/configs/screenshots/M4_Spindle_on.png while im reading look at the new "old mashine "we got https://www.maschinensucher.de/vid/3428227.mp4 best is the spindle closer change part from Vertical to horizontal and back better not get in it's way quite a versatile machine 3500USD + moving the school has a JohnDerr truck to move things setp scale.0.gain 60.00 isent this in ticks as 60*4 iirc that's for the spindle display * TurBoss has joined #linuxcnc setp pid.0.maxerror 200 isent this to high maybe it's working. m19? i could lower it i suppose JT-Shop, no that's the regular pid it seams to be alright but pid 1 does not connect to spindle on where should it connect? isn't motion.spindle-on an output? it's working. ?? not pid1 pid0 does they both go thru mux2 ok to be shure S300 M3 pid 0 is enabled and spindle runs yes m5 pid0 disabled pid 1 enabled no, mux2 defaults to pid0 mux2 is switched when pid1 goes active M19 activates it IchGucksLive, Austin is pretty far inland, i'm not too concerned that's why i took screenshots of M3 M4 and M19 also my house is basically on a hill, so water runs off pretty well peepsalot: it will come soon has anyone here worked with epoxy granite? Tom_L: there is somkind of a miscalculation should motion.spindle-on go true during orient mode? image showes orient pos 34Deg goto 10deg -282 posi error * DaPeace has joined #linuxcnc Tom_L: i think no as it is triggerd tom did you check the signaling by moving the spindle manuell * miss0r has joined #linuxcnc turning the spindle affects the position and error orient.0 pos error and the pid shoudt move also iirc it was * FAalbers has joined #linuxcnc Tom_L: as i read the system the index needs to be connected line 481 pid.1.index-enable otherewise it does not go beond zero woops i'll try that pid.0.maxoutput is set to 1000 * DaPeace has quit IRC (Quit: Leaving.) ~500 rpm just until i get it turning the image showes positiv move from 34Deg to 10 so it is 336Deg to go on a 2000 ticks encoder * DaPeace has joined #linuxcnc * molaf has quit IRC (Ping timeout: 255 seconds) 2000/360=5,5tick per deg *3361866 ticks to go limitet to 1000 no move 2000/360=5,5tick per deg *336=1866 ticks to go isn't that just he pid command to the DAC for voltage out? the max 1000 limit as i read the maxoutput soudt be set to 0 at spindle tuning for the purpose of getting the spindle turning, i figued i would set high numbers and limit the output. it is only going to turn one revolution anyway ok so it snaps to the limit and stays there i'll refine it once it works so i dont see motion.spindle-speed-out in the halshow does this go to a value abs.0.in and pid.0.command 513 net spindle-cmd-abs abs.2.out => hm2_[HOSTMOT2](BOARD).0.pwmgen.00.value so the value is to the pwm * ve7it has joined #linuxcnc yes net velocity-mode motion.spindle-on => hm2_[HOSTMOT2](BOARD).0.pwmgen.00.enable pid.0.enable hm2_[HOSTMOT2](BOARD).0.gpio.039.out 39 is unused atm pwm isent enabled by pid 1 * DaPeace has quit IRC (Quit: Leaving.) would i need an or2 for that? i think yes err, pid.x.enable is input so not from that motion.spindle-on enables those that's why i'm wondering if orient is a special mode guys, how can i check the speed that i can get an stepper running? is possible to calculate an estimated value? but orient needs in someway connect to pwm samsagaz: look into the datasheet yeah, i'm going to look at it more later today need to run right now... IchGucksLive, ok if you have any more thoughs i'll read later