#linuxcnc Logs
Oct 22 2024
#linuxcnc Calendar
12:10 AM lcnc-relay: <meisterdippel@discord> moin
01:54 AM Deejay: moin
02:15 AM lcnc-relay: <travis_farmer@discord> Morning
03:54 AM lcnc-relay: <vibram@discord> hello
03:55 AM mrec: finally after a half year the mitsubishi CNC can be used properly, even trochoidal milling works well (CAM freecad)
03:56 AM mrec: as a nice bonus the mitsubishi system can use the linuxcnc post processor
03:57 AM mrec: repair & upgrade cost 800$
03:57 AM mrec: 1.1m x 0.65m milling area
03:58 AM mrec: I'd say that machine is the absolute minimum that still makes sense to use nowadays anything lower than Meldas M65 is not worth it
03:59 AM mrec: drip feeding 19.2kbaud is way too slow for freecad trochoidal milling, however it has some 2gb flash disk which is acceptable
04:19 AM JT-Cave: morning
04:30 AM lcnc-relay: <travis_farmer@discord> Morning
04:36 AM Tom_L: morning
04:37 AM Tom_L: JT-Cave, 7:34Pm: http://tom-itx.no-ip.biz:443/~tom-itx/irc/logs/%23linuxcnc/2024-10-21.html
04:38 AM Tom_L: travis ^^
04:45 AM lcnc-relay: <travis_farmer@discord> i think i solved it Tom_L, it was a merge error because my code worked. i just have to test before i release the PR
04:47 AM lcnc-relay: <travis_farmer@discord> or i can push the fix now, just to get it fixed... JT?
04:47 AM Tom_L: code, test, retest, push ;)
04:48 AM lcnc-relay: <travis_farmer@discord> that's what i thought, wasn't sure how urgent it was
04:48 AM Tom_L: then i'll break it :)
04:48 AM Tom_L: urgent enough i can't launch flex
04:48 AM lcnc-relay: <travis_farmer@discord> mine launches fine 😛
04:49 AM Tom_L: that's why we test on more than one setup
04:49 AM Tom_L: jt and i have run across that multiple times
04:49 AM lcnc-relay: <travis_farmer@discord> like i said, it was an error when i merged. the line was there when i coded it
04:53 AM Tom_L: paste the line and i'll test it
04:53 AM -!- #linuxcnc mode set to +v by ChanServ
05:04 AM lcnc-relay: <travis_farmer@discord> flexgui/flexgui/src/libflexgui/startup.py
05:04 AM lcnc-relay: <travis_farmer@discord> line: 1209
05:04 AM lcnc-relay: <travis_farmer@discord> insert " hal_lcd = []"
05:04 AM Tom_dev: past the line abov and below it too
05:04 AM lcnc-relay: <travis_farmer@discord> hal_sliders = []
05:04 AM lcnc-relay: hal_lcd = []
05:04 AM lcnc-relay: parent.hal_readers = {}
05:04 AM lcnc-relay: <travis_farmer@discord> discord killed the tabbing, but you get the idea
05:58 AM -!- #linuxcnc mode set to +v by ChanServ
06:01 AM JT-Cave: travis you need to test this bit of code out https://github.com/jethornton/flexgui/blob/master/flexgui/src/libflexgui/startup.py#L1239
06:01 AM JT-Cave: and https://github.com/jethornton/flexgui/blob/master/flexgui/src/libflexgui/startup.py#L1248
06:02 AM JT-Cave: hmm nevermind
06:08 AM lcnc-relay: <travis_farmer@discord> ???
06:10 AM JT-Cave: nevermind
06:10 AM lcnc-relay: <travis_farmer@discord> had me confused 😉
06:46 AM JT-Cave: had me cornfused too
06:59 AM lcnc-relay: <travis_farmer@discord> i was watching the recent WWW video, where he got an old Hurco VM1 🙂
07:16 AM lcnc-relay: <travis_farmer@discord> <-- needs a bit of breakfast...
07:23 AM JT-Cave: https://youtu.be/kTFMM71VFuU
07:31 AM Tom_L: is this what AI coding is like?
07:31 AM Tom_L: drag, drop, slap a name on it...
07:34 AM lcnc-relay: <travis_farmer@discord> is that a poke at me?
07:37 AM Tom_L: watching jt's video
07:37 AM lcnc-relay: <travis_farmer@discord> ok
07:40 AM Tom_L: unless of course you're feelin guilty :)
07:42 AM -!- #linuxcnc mode set to +v by ChanServ
07:42 AM lcnc-relay: <travis_farmer@discord> always feeling guilty for some reason 😉
07:43 AM lcnc-relay: <travis_farmer@discord> but i don't use Ai for code
07:43 AM Tom_L: it was a comment about how easy flex is to get going
07:44 AM lcnc-relay: <travis_farmer@discord> oh, i just take things way to personally sometimes. 🙂
07:45 AM Tom_L: i noticed
07:45 AM Tom_L: bad idea on irc
07:46 AM Tom_L: JT-Cave, #155
08:03 AM -!- #linuxcnc mode set to +v by ChanServ
08:03 AM -!- #linuxcnc mode set to +v by ChanServ
08:08 AM lcnc-relay: <skunkworks8841@discord> as you get older - you either stop caring about what others say - or you get more and more angry.. I am the former.
08:11 AM lcnc-relay: <travis_farmer@discord> judging by the number of meds i need to be on, i suspect i am the "more angry" type 😉
08:11 AM Tom_L: well, don't take it personal here
08:12 AM lcnc-relay: <skunkworks8841@discord> lol.
08:12 AM Tom_L: at least in the channels i frequent irc is alot milder than it was 20 yrs ago
08:13 AM lcnc-relay: <travis_farmer@discord> i wasn't much in IRC 20 years ago... more into NNTP... 😉
08:14 AM bjorkintosh: a lot. because the angriest ones have either moved on to other platforms (twitter etc) or simply don't use irc anymore.
08:15 AM Tom_L: i haven't seen a good kick ban war in ages :)
08:21 AM lcnc-relay: <onceloved.cn@discord> When the program is running, the spindle does not stop but continues to rotate after manually stopping the program. Is this normal? Is there any solution to make the spindle stop rotating after manually stopping the program?
08:21 AM lcnc-relay: <onceloved.cn@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/NtNsSNkcYFIaCLFBLHLRmmuJ/QQ20241022-21714.mp4
08:37 AM Tom_L: that looks like a turboss or lcvette question
08:37 AM Tom_L: they have a probe basic channel on discord or matrix? dunno which
08:38 AM Tom_L: and are here sometimes
08:38 AM Tom_L: oh wait, that's dragon
08:38 AM Tom_L: looks alot like probe basic to me
08:39 AM lcnc-relay: <onceloved.cn@discord> 🤣
08:39 AM lcnc-relay: <onceloved.cn@discord> Have you woken up yet?
08:39 AM Tom_L: not really
08:39 AM lcnc-relay: <Lcvette> Yeah dragon, i would check the forum in the qtvcp section
08:40 AM Tom_L: just had a root canal... drugged
08:44 AM lcnc-relay: <onceloved.cn@discord> After running the program on the pb interface and manually stopping the program, the spindle will also stop and the speed will be displayed as 0.
08:44 AM Tom_L: must be a gui 'feature', flex or axis don't behave that wa
08:44 AM Tom_L: y
08:46 AM Tom_L: in the docs: QtDragon and QtVCP are relatively new programs added into LinuxCNC. Bugs and oddities are possible. Please test carefully when using a dangerous machine. Please forward reports to the forum or maillist.
08:46 AM Tom_L: dunno who maintains it
08:47 AM Tom_L: Persei8
08:47 AM Tom_L: and others
09:00 AM lcnc-relay: <travis_farmer@discord> <-- heads out to test his cool looking UI for stylesheet changes 🙂
09:00 AM Tom_L: you should build a sim so you can test it there
09:04 AM lcnc-relay: <travis_farmer@discord> On my laptop?
09:06 AM Tom_L: why not?
09:07 AM lcnc-relay: <travis_farmer@discord> Windows
09:07 AM Tom_L: copy a sim from one of the examples and put your ui on it
09:07 AM Tom_L: oh
09:07 AM Tom_L: nevermind
09:07 AM lcnc-relay: <travis_farmer@discord> 🙂
09:09 AM JT-Cave: travis I have a dual boot on my laptop so I can run debian
09:34 AM lcnc-relay: <travis_farmer@discord> my laptop won't dual boot. i have a linux HDD and a Windows SSD and it only shows the Windows boot option
09:35 AM lcnc-relay: <travis_farmer@discord> check out them LCDs 🙂
09:35 AM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/WsCIahXZMUyapJhvPdsdvCUx/Screenshot_from_2024-10-22_10-24-13.png
09:36 AM Tom_L: nice
09:36 AM Tom_L: blue on black is a little hard for me to see
09:37 AM lcnc-relay: <travis_farmer@discord> yeah, changing to yellow
09:37 AM Tom_L: lt blue maybe
09:40 AM lcnc-relay: <travis_farmer@discord> thats lighter, but i am still thinking yellow?
09:40 AM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/ALTwJPhmyxktjtFDkgUegExp/Screenshot_from_2024-10-22_10-32-16.png
09:42 AM lcnc-relay: <travis_farmer@discord> definatly yellow, temp needs to be seen
09:42 AM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/TVgELdpUDwvptLiTxhsPxCBK/Screenshot_from_2024-10-22_10-34-37.png
10:25 AM lcnc-relay: <travis_farmer@discord> Hmmm, lunch time, i suppose...
10:37 AM lcnc-relay: <skunkworks8841@discord> This all looks so cool.
11:45 AM lcnc-relay: <travis_farmer@discord> what, my Flex interface?
11:46 AM lcnc-relay: <travis_farmer@discord> well, my UI rendition, JT's Flex Interface...
11:47 AM lcnc-relay: <skunkworks8841@discord> The flex-abillity of it..
11:47 AM lcnc-relay: <travis_farmer@discord> yeah, it is really cool 🙂 and gets better and better the more i use it
11:49 AM Tom_L: can you post the lcd part of your qss somewhere?
11:50 AM lcnc-relay: <travis_farmer@discord> sure can
11:50 AM Tom_L: JT-Cave, maybe somebody can talk you into making all numerics available in lcd too?
11:50 AM Tom_L: christmas is coming up ya know...
11:51 AM Tom_L: just a wishlist thought
11:52 AM lcnc-relay: <travis_farmer@discord> https://paste.debian.net/1333086/
11:52 AM lcnc-relay: <travis_farmer@discord> LOL, Tom_L 😉
11:53 AM Tom_L: thanks
11:53 AM lcnc-relay: <travis_farmer@discord> np
11:53 AM Tom_L: i know how busy he is right now
11:54 AM lcnc-relay: <travis_farmer@discord> yeah, with the panel and all
11:55 AM JT-Cave: Tom_L, just added some checks for hal buttons
11:55 AM Tom_L: jt i saw that but didn't know if you were ready for another deb
11:56 AM JT-Cave: and debugged it :)
11:56 AM JT-Cave: yup
11:56 AM Tom_L: :)
11:56 AM JT-Cave: nap time here
11:56 AM Tom_L: ok
11:56 AM Tom_L: just had one of those
11:56 AM JT-Cave: lunch time coding is done
11:56 AM Tom_L: having lunch atm
11:56 AM Tom_L: lost 10lb since the 11th
11:57 AM Tom_L: dash works
11:57 AM Tom_L: pants are falling off now
11:58 AM lcnc-relay: <travis_farmer@discord> thats a scary sight
11:58 AM lcnc-relay: <travis_farmer@discord> 😉
11:58 AM Tom_L: i'd just gotten some a size larger...
11:59 AM roycroft: my power supply got shipped back from portland to eugene yesterday, and then back to portland last night
11:59 AM roycroft: this will be the third time it's gone to eugene then portland
11:59 AM * roycroft hopes the usps figures out how to deliver it soon, as he needs his laptop
12:00 PM lcnc-relay: <travis_farmer@discord> <-- sends roycroft some of his laptop power 😉
12:02 PM Tom_L: JT-Cave, PR #156
12:15 PM lcnc-relay: <travis_farmer@discord> with some messing with the BIOS, i got my laptop to boot the linux HDD...
12:27 PM lcnc-relay: <travis_farmer@discord> man this hard drive is slow compared to my SSD... i don't miss the days of spinning rust...
12:29 PM lcnc-relay: <skunkworks8841@discord> lol.. Yes - I don't think I have had to deal with a spinny disk for ages..
12:29 PM lcnc-relay: <skunkworks8841@discord> I think the K&T now has an ssd..
12:29 PM lcnc-relay: <travis_farmer@discord> but this laptop won't take two SSDs
12:31 PM lcnc-relay: <travis_farmer@discord> i suppose i could get a SATA SSD at some point...
12:48 PM lcnc-relay: <travis_farmer@discord> LinuxCNC is installed, now for flex 🙂
12:53 PM lcnc-relay: <skunkworks8841@discord> we have over 150tb of spinning rust here
12:53 PM lcnc-relay: <skunkworks8841@discord> (it is probably more than that)
01:04 PM Tom_L: http://tom-itx.no-ip.biz:443/~webpage/cnc/JT-SHOP/flexgui/touch-probe3-lcd.png
01:04 PM lcnc-relay: <travis_farmer@discord> Hmmm, VScode crashes on Linux...
01:05 PM lcnc-relay: <travis_farmer@discord> Nice, Tom_L 🙂
01:05 PM Tom_L: lcd take more realestate
01:05 PM lcnc-relay: <travis_farmer@discord> yeah, but they loog good
01:05 PM Tom_L: i think so
01:08 PM lcnc-relay: <travis_farmer@discord> holy crap, this laptop has the worst latency i have ever seen!!!
01:08 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/eahVrtFpDOvaiLniztiIdopK/Screenshot_from_2024-10-22_14-01-22.png
01:09 PM lcnc-relay: <travis_farmer@discord> oh, non RT kernal, BRB
01:10 PM Tom_L: may not improve alot on a laptop
01:14 PM lcnc-relay: <travis_farmer@discord> i was only curious 😉
01:16 PM lcnc-relay: <travis_farmer@discord> better, but still no worse than my machine computer...
01:23 PM lcnc-relay: <travis_farmer@discord> with YouTube running... not horrific... could almost run a machine
01:23 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/iINNmHNAsDGQQgFHsXkcFSCX/Screenshot_from_2024-10-22_14-14-59.png
01:26 PM Tom_L: set isolcpus and it may improve
01:26 PM Tom_L: in the kernel
01:26 PM Tom_L: i use grub customizer for that
01:27 PM lcnc-relay: <travis_farmer@discord> nah, i was only curious. gotta save this laptop for CAD and Dev, not machine work 😉
01:28 PM Tom_L: quiet isolcpus2,3,etc idle=poll
01:28 PM Tom_L: i'd be curious
01:28 PM Tom_L: it only applies to the linux drive
01:29 PM Tom_L: it's a kernel setting
01:29 PM lcnc-relay: <travis_farmer@discord> where do i get grub customizer
01:29 PM Tom_L: mine has 4 cores
01:30 PM Tom_L: it's in synaptic package manager
01:31 PM Tom_L: under general settings -> kernel parameters
01:33 PM lcnc-relay: <travis_farmer@discord> set, BRB
01:38 PM * JT-Shop brings the engine hoist from the other shop in here to handle the ginormas panel
01:39 PM lcnc-relay: <travis_farmer@discord> Tom_L
01:39 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/WGTSHdsEmoaoJIFWtcUldngx/Screenshot_from_2024-10-22_14-31-46.png
01:39 PM Tom_L: JT-Shop, wait til you get it full
01:40 PM Tom_L: travis, try fewer cores etc to find the best result
01:40 PM lcnc-relay: <travis_farmer@discord> ok
01:40 PM JT-Shop: when it's full it's out of here :)
01:41 PM Tom_L: yup
01:41 PM Tom_L: you started on the stations already haven't you?
01:41 PM Tom_L: what sort of connection do those have to the main pannel?
01:41 PM JT-Shop: 203 lbs empty
01:42 PM JT-Shop: remote stations are done except for the pots and I got the reducers today to finish that up
01:52 PM lcnc-relay: <travis_farmer@discord> i think thats as good as this laptop is going to get...
01:52 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/WDSylkCrWqxIGgWJqcLyoiRh/Screenshot_from_2024-10-22_14-44-17.png
01:53 PM Tom_L: https://x.com/boxcardavid/status/1848608391310291297?t=5LPGvbdUzMRL0qV1ATLLSA
01:53 PM Tom_L: travis, ethernet might work off that
01:54 PM lcnc-relay: <travis_farmer@discord> perhaps, debian is a little jittery, so who knows how well
01:55 PM lcnc-relay: <travis_farmer@discord> good enough for a sim
01:55 PM lcnc-relay: <skunkworks8841@discord> that is more than good enough for external interfaces like mesa
01:56 PM lcnc-relay: <skunkworks8841@discord> I used my laptop for a long time testing ethernet mesa configs.. (it had <100us latency)
01:56 PM lcnc-relay: <travis_farmer@discord> it is near where my machine computer runs, but that must be set to 1000000 servo period to even work
01:57 PM lcnc-relay: <travis_farmer@discord> brb, booting back into windows
01:57 PM lcnc-relay: <skunkworks8841@discord> Tom_L: a while back someone on cnczone was trying to do something similar
01:57 PM Tom_L: neat
02:03 PM lcnc-relay: <skunkworks8841@discord> https://www.cnczone.com/forums/linear-and-rotary-motion/13593-forum.html
02:04 PM lcnc-relay: <travis_farmer@discord> what a PITA to dual-boot this laptop... gotta change the BIOS every time
02:05 PM Tom_L: travis, you know you can combine widgets in the qss, you don't need a separate function for each one?
02:05 PM -!- #linuxcnc mode set to +v by ChanServ
02:06 PM lcnc-relay: <travis_farmer@discord> really? that would make it easier
02:06 PM Tom_dev: QLCDNumber#Cycle_Hrs_lcd, QLCDNumber#Cycle_Min_lcd, QLCDNumber#Cycle_Sec_lcd{
02:06 PM Tom_dev: for example
02:06 PM lcnc-relay: <travis_farmer@discord> ok, cool
02:08 PM lcnc-relay: <JT> https://jauriarts.org/_matrix/media/v3/download/matrix.org/oIDtYMxlYppdPPPplWikkXFk/1000002511.jpg
02:08 PM Tom_L: you could take a nap in that thing
02:10 PM JT-Shop: put an outboard motor on and go fishing
02:10 PM lcnc-relay: <travis_farmer@discord> lol
02:11 PM Tom_L: https://visitnebraska.com/trip-idea/tanking-incredible-floating-sensation
02:11 PM JT-Shop: lol
02:14 PM Tom_L: travis, you can also set some properties that way then single them out with others in another section if you want
02:15 PM lcnc-relay: <travis_farmer@discord> JT, just noticed the doc note under your hal label is funky, the one i copied from...
02:17 PM lcnc-relay: <travis_farmer@discord> note the LCD note you fixed of mine, VS the note above it
02:17 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/mxhohUcEfdujzNKtQePmYphM/Screenshot_2024-10-22_at_15-09-59_HAL_Pins_Flex_GUI_documentation.png
02:19 PM lcnc-relay: <travis_farmer@discord> i will do a PR for you 🙂
02:25 PM lcnc-relay: <travis_farmer@discord> PR #157
02:25 PM lcnc-relay: <travis_farmer@discord> i tested it
02:26 PM lcnc-relay: <travis_farmer@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/ZaRYYVRjUrFVuYunOmsNitlX/Screenshot_2024-10-22_at_15-18-43_HAL_Pins_Flex_GUI_documentation.png
02:27 PM lcnc-relay: <travis_farmer@discord> it could have been my mistake from the first doc edit...
02:30 PM lcnc-relay: <travis_farmer@discord> i feel like a full developers assistant now 😉
02:32 PM lcnc-relay: <travis_farmer@discord> or a developers puppy-dog... one or the other... 🤣
02:38 PM lcnc-relay: <JT> https://jauriarts.org/_matrix/media/v3/download/matrix.org/jOTCVcHmhTTxnxPAbDoVSWzS/1000002512.jpg
02:38 PM * JT-Shop takes 5
02:39 PM lcnc-relay: <travis_farmer@discord> you earned it. that must have been a struggle
02:40 PM JT-Shop: lots of walking back and forth carrying 4x4's and stuff like the engine hoist a piece at a time
02:41 PM lcnc-relay: <travis_farmer@discord> whats the dimensions for that cabinet?
02:49 PM * roycroft almost finished sanding another wall panel at lunch time today, and should easily be able to finish that and install it after work
02:50 PM roycroft: then it's time to putty up the screw holes, sand the putty when it's set, and paint
02:50 PM lcnc-relay: <JT> https://jauriarts.org/_matrix/media/v3/download/matrix.org/kukysjlWnSzkiNKtpJSADrsB/1000002513.jpg
02:50 PM roycroft: i'm really looking forward to painting the walls
02:50 PM JT-Shop: 48T 37W 16D
02:50 PM roycroft: it's going to make a huge difference in the appearance of the shop - it will look bright and finished
02:52 PM roycroft: Linux zabbtest 6.6.51+rpt-rpi-v8 #1 SMP PREEMPT Debian 1:6.6.51-1+rpt3 (2024-10-08) aarch64 GNU/Linux
02:53 PM roycroft: so raspberry pi os ships withe a pre-empt kernel by default now
02:54 PM roycroft: or maybe it has for a while and i just now noticed
02:54 PM lcnc-relay: <travis_farmer@discord> "48T 37W 16D" that is much bigger than i thought! too big for my machine panel
02:55 PM Tom_L: JT-Shop, don't let the door weight tip it ;)
02:59 PM JT-Shop: it's staying tied up to the hoist...
02:59 PM Tom_L: good idea
03:00 PM Tom_L: do you take the inner pannel out to mount things?
03:04 PM JT-Shop: yup, the subpanel has to come out to drill and tap and fasten all the components
03:04 PM JT-Shop: and putz with their layout
03:04 PM Tom_L: get the vfds yet?
03:05 PM JT-Shop: no
03:06 PM JT-Shop: the subpanel is 50 lbs so a 1/4 of the weight
03:06 PM Tom_L: might be fun getting in and out
03:33 PM JT-Shop: wasn't bad getting the subpanel out...
03:47 PM lcnc-relay: <nortonantivirus2015@discord> Hello, i was wondering if anyone has any experience with Parallel SCARA kinematics in LinuxCNC...? I am looking at trying to use this within LinuxCNC to see if i can enable some form of backlash compensation or closed loop control
03:47 PM lcnc-relay: <nortonantivirus2015@discord> https://jauriarts.org/_matrix/media/v3/download/jauriarts.org/ZxfBNKigdzSSViXmrpcKXFZy/AP1GczO2mEOsUWJQGrDUIEz8HgnjrJ_hJzOCmHc4cqyK_8PVkgEtklIpYfdXZww1714-h1270-s-no-gm.png
04:24 PM -!- #linuxcnc mode set to +v by ChanServ
04:26 PM Tom_L: nortonantivirus look on the forum
04:27 PM Tom_L: https://forum.linuxcnc.org/10-advanced-configuration/49469-five-bar-parallel-scara-kinematic
04:57 PM roycroft: the panel is installed
04:57 PM * roycroft can focus on wood putty and final paint prep soon
04:58 PM roycroft: the shop looks smaller with the wall panels up, but i think when they are painted it will look bigger
05:04 PM * roycroft is going to work on mounting and ducting the dust collector while the wood putty is drying
05:05 PM lcnc-relay: <nortonantivirus2015@discord> Tom_L: thanks! I will look into this
05:14 PM Tom_L: 86°F
05:25 PM JT-Shop: 79°F
06:01 PM * JT-Shop calls it a night
06:35 PM lcnc-relay: <big_kevin420@discord> @Tom_L yeah those roller screws are good for presses
07:05 PM lcnc-relay: <skunkworks8841@discord> big_kevin420@discord yes. My head is huge...
07:17 PM lcnc-relay: <big_kevin420@discord> 125% scale that print
07:18 PM lcnc-relay: <skunkworks8841@discord> lol - probably more than enough
07:22 PM lcnc-relay: <skunkworks8841@discord> I always had to tighten the welding helmet after dad used it.. When he was fighting cancer - I had to make it bigger to fit my head.. That was an eye opener..
08:36 PM lcnc-relay: <big_kevin420@discord> that one med that makes you swell up like a balloon?
09:05 PM rdtsc is now known as rdtsc_away
09:15 PM roycroft: this is only remotely analagous, but i've had to replace all my wrist watch bands since i broke my wrist
09:16 PM roycroft: none of the watches would fit any more - as my wrist is larger than it was
09:27 PM xxcoder: fun change
09:27 PM xxcoder: I hope it never happens to me, my wrists is big enough already thanks
10:16 PM -!- #linuxcnc mode set to +v by ChanServ