#linuxcnc-devel Logs

Jan 16 2023

12:02 AM linuxcnc-build2_: Build [#181](http://buildbot2.highlab.com/buildbot/#builders/13/builds/181) of `00-checkin` 3completed successfully.
01:02 AM -!- #linuxcnc-devel mode set to +v by ChanServ
01:53 AM pere: Tom_L: the spindle(9) man page do not mention any index related pins?
03:21 AM linuxcnc-build2_: Build [#184](http://buildbot2.highlab.com/buildbot/#builders/13/builds/184) of `00-checkin` 4failed.
04:32 AM Tom_L: pere, http://linuxcnc.org/docs/stable/html/man/man9/motion.9.html#SPINDLE%20PINS
04:32 AM Tom_L: spindle.M.index-enable I/O BIT
04:32 AM Tom_L: For correct operation of spindle synchronized moves, this signal must be hooked to the index-enable pin of the spindle encoder.
04:39 AM Tom_L: pere, years back before multi spindle, it was 'motion.spindle.xxx' now it should be spindle.x.xxx but on that pin it isn't. it is spindle-index-enable
04:40 AM Tom_L: but
04:40 AM Tom_L: i can't get it to work in the hal file, only using mdi
04:41 AM Tom_L: but in hal show it still shows it as spindle.0.index-enable
04:42 AM Tom_L: you can likely test it with: sets spindle-index-enable TRUE then test sets spindle.0.index-enable TRUE
04:42 AM Tom_L: i'm running 2.8.4
05:00 AM linuxcnc-build2_: Build [#185](http://buildbot2.highlab.com/buildbot/#builders/13/builds/185) of `00-checkin` 3completed successfully.
05:10 AM pere: Tom_L: can this spindle sync stuff be used to position a spindle servo motor with an encoder, for tool changes?
05:12 AM pere: perhaps the spindle man page should have a cross reference to motion(9)?
06:41 AM Tom_L: yes
06:41 AM Tom_L: to spindle orient
06:42 AM Tom_L: that's what i'm working on currently
06:56 AM Tom_L: as far as spindle & motion comps, i don't know the origins of them or how they relate to each other
08:30 AM pere: Me neither, but it seem like a good idea to make manual page readers aware that they would be useful reads if starting in one of them.
09:23 AM seb_kuzminsky: good morning :-)
09:26 AM pere: good morning. :)
10:22 AM roguish[m]: good morning...
10:23 AM roguish[m]: seb_kuzminsky: andyP pushed a fix for the halcompile extra agrs and stuff. has that made it into your .deb in buildbot2 ???
10:24 AM roguish[m]: https://github.com/LinuxCNC/linuxcnc/issues/2204#issuecomment-1383249239
11:46 AM linuxcnc-build2_: Build [#190](http://buildbot2.highlab.com/buildbot/#builders/13/builds/190) of `00-checkin` 4failed.
01:21 PM linuxcnc-build2_: Build [#191](http://buildbot2.highlab.com/buildbot/#builders/13/builds/191) of `00-checkin` 3completed successfully.
01:48 PM JT-Shop: pcw--home, do you have more 7i96S's in process?
01:50 PM pcw--home: Yes, we're down to about 20 stock but close to receiving another batch of 500
01:50 PM pcw--home: also should get 7I92T[X]s this week
01:52 PM JT-Shop: cool
01:52 PM JT-Shop: did you find a reject 7i97?
01:56 PM pcw--home: Forgot to check, will do that when I go into work tomorrow
01:57 PM JT-Shop: ok, thanks
03:04 PM -!- #linuxcnc-devel mode set to +v by ChanServ
06:56 PM linuxcnc-build2_: Build [#146](http://buildbot2.highlab.com/buildbot/#builders/2/builds/146) of `50-deb-uspace.debian-12-bookworm-amd64` 4failed.
10:34 PM -!- #linuxcnc-devel mode set to +v by ChanServ