#linuxcnc-devel Logs

Dec 19 2022

12:40 AM -!- #linuxcnc-devel mode set to +v by ChanServ
12:47 AM fdarling: is there a way to "pause" LinuxCNC's engine until after you are able to open up HALscope, so that you can see certain things that happen upon startup?
02:28 AM linuxcnc-build2: Build [#10](http://buildbot2.highlab.com/buildbot/#builders/11/builds/10) of `10-rip.debian-12-bookworm-rtpreempt-amd64` 4failed.
02:45 AM linuxcnc-build2: Build [#11](http://buildbot2.highlab.com/buildbot/#builders/13/builds/11) of `00-checkin` 4failed.
03:02 AM linuxcnc-build2: Build [#11](http://buildbot2.highlab.com/buildbot/#builders/11/builds/11) of `10-rip.debian-12-bookworm-rtpreempt-amd64` 8completed with warnings.
03:14 AM linuxcnc-build2: Build [#12](http://buildbot2.highlab.com/buildbot/#builders/13/builds/12) of `00-checkin` 3completed successfully.
06:29 AM pere: is there a command line tool to validate linuxcnc configuration without starting linuxcnc?
07:12 AM linuxcnc-build2: Build [#14](http://buildbot2.highlab.com/buildbot/#builders/11/builds/14) of `10-rip.debian-12-bookworm-rtpreempt-amd64` 4failed.
07:31 AM linuxcnc-build2: Build [#15](http://buildbot2.highlab.com/buildbot/#builders/13/builds/15) of `00-checkin` 4failed.
07:54 AM linuxcnc-build2: Build [#15](http://buildbot2.highlab.com/buildbot/#builders/11/builds/15) of `10-rip.debian-12-bookworm-rtpreempt-amd64` 8completed with warnings.
08:01 AM fdarling: pere: probably not, since the HAL pins are populated at runtime, especially by drivers like HostMot2
08:08 AM linuxcnc-build2: Build [#16](http://buildbot2.highlab.com/buildbot/#builders/13/builds/16) of `00-checkin` 3completed successfully.
08:08 AM pere: was hoping to find a way to detect typos and misfeatures in the configs/ directory automatically.
01:31 PM linuxcnc-build: build #6109 of 1510.rip-jessie-rtpreempt-i386 is complete: Failure [4failed configure-debian-control] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1510.rip-jessie-rtpreempt-i386/builds/6109 blamelist: andypugh <andy@bodgesoc.org>
01:35 PM seb_kuzminsky: not sure why the jessie-rtpreempt-i386 worker in the old buildbot sometimes fails like that...
01:54 PM roguish[m]: do 'we' really need a 32bit any more? really?
01:55 PM roguish[m]: just thinking to reduce the workload...
02:05 PM cradek: as someone who's definitely stuck on old hardware, I don't feel too put out that I'm also stuck on an old version of linuxcnc
02:06 PM cradek: (I do hope to fix both problems in the coming months, but who knows)
02:08 PM roguish[m]: I just don't want seb and his buddy bots to be over worked....
03:17 PM Tom_L: cradek, how old is your hardware?
03:17 PM Tom_L: pretty sure mine is running 32bit
03:17 PM Tom_L: wheezy
03:52 PM linuxcnc-build: build #9518 of 0000.checkin is complete: Failure [4failed] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/0000.checkin/builds/9518 blamelist: andypugh <andy@bodgesoc.org>
03:53 PM roguish[m]: if it works, don't mess with it without a really, really good reason.....
03:54 PM Tom_L: now where's the fun in that??
03:54 PM Tom_L: it's one of those j1900 MB
03:54 PM Tom_L: not much newer would work on it i believe
03:54 PM Tom_L: because of RTAI
03:58 PM Tom_L: but i am able to run 2.8.4 lcnc
04:32 PM cradek: Tom_L: it's a Pentium II
04:34 PM cradek: Linux lathe 3.4-9-rtai-686-pae #1 SMP PREEMPT Debian 3.4.55-3linuxcnc i686