#linuxcnc-devel Logs

Aug 03 2022

02:18 AM pere: silopolis[m]: yeah, but I hope the packaging can stabilize soon.
02:35 AM silopolis[m]: pere: We all support you guys in this tedious work. Hasta la victoria ✊
04:56 AM -!- #linuxcnc-devel mode set to +v by ChanServ
05:01 AM -!- #linuxcnc-devel mode set to +v by ChanServ
03:24 PM pere: hi
04:37 PM Tom_L: hi
04:45 PM silopolis[m]: o/
04:51 PM -!- #linuxcnc-devel mode set to +v by ChanServ
04:51 PM Tom_dev: make[2]: *** No rule to make target '../docs/man/man1/halstreamer.1', needed by 'depends/man1/halstreamer.1.d'. Stop.
04:51 PM Tom_dev: debian 11
04:53 PM Tom_dev: debian/configure no-docs
04:53 PM Tom_dev: asciidoc: FAILED: Python 3.5 or better required
04:53 PM Tom_dev: make[2]: *** No rule to make target '../docs/man/man1/halstreamer.1', needed by 'depends/man1/halstreamer.1.d'. Stop.
04:53 PM Tom_dev: aparently that switch doesn't work
04:55 PM Tom_dev: Python 3.10.5 (main, Jun 8 2022, 09:26:22) [GCC 11.3.0] on linux
04:57 PM JT-Cave: no-docs worked for me on debian 11.4
04:57 PM Tom_dev: i'm gonna wipe it clean and start all over
04:58 PM JT-Cave: trying TurBoss dpkg-buildpackage switches now
04:58 PM Tom_dev: which is?
04:58 PM JT-Cave: debuild -b -uc
04:58 PM Tom_dev: before i wipe it?
04:58 PM JT-Cave: with just debian/configure
04:58 PM JT-Cave: up to you
04:59 PM JT-Cave: I'll let you know in a bit if it builds the docs without error or not
04:59 PM Tom_dev: not debuild?
04:59 PM Tom_dev: i bet it doesn't
04:59 PM Tom_dev: not using the no-docs switch?
05:00 PM Tom_dev: nevermind.. i misread something
05:00 PM Tom_dev: asciidoc: FAILED: Python 3.5 or better required
05:00 PM Tom_dev: make[2]: *** No rule to make target '../docs/man/man1/halstreamer.1', needed by 'depends/man1/halstreamer.1.d'. Stop.
05:01 PM Tom_dev: with debian/configure
05:01 PM Tom_dev: and debuild -b -uc
05:03 PM JT-Cave: debian 11 has python 3.9.2
05:04 PM JT-Cave: are you sure your on debian 11.4?
05:04 PM Tom_L: i think it pulled stuff from sid
05:04 PM Tom_L: because of that po4a thing
05:04 PM JT-Cave: cat /etc/debian_version
05:04 PM JT-Cave: I never did anything with pooa
05:04 PM Tom_L: yeha
05:05 PM JT-Cave: https://gnipsel.com/linuxcnc/debian-11-emc.html
05:05 PM Tom_L: 11.4
05:05 PM Tom_L: i'll start over
05:05 PM JT-Cave: something is screwy for sure if asciidoc complains about python 3.5 or better
05:06 PM JT-Cave: the only thing different than the web page is the debuild switch
05:06 PM JT-Cave: I'll come back down and check in a bit
05:06 PM Tom_L: i got a dvd i'll start a fresh install
05:10 PM Tom_L: can you post your sources list somewhere?
05:10 PM Tom_L: i copied what i had and saved it
05:14 PM Tom_L: i noticed you listed debhelper 2x.. once on the single line and once in the group of installs
05:16 PM Tom_L: should just skip it anyway
05:22 PM JT-Shop: I didn't change debian 11.4 souces.list I don't think
05:22 PM Tom_L: well i had to on mine because the first time it defaulted to just the dvd
05:23 PM JT-Shop: debhelper x 2 is a typo I think
05:23 PM Tom_L: it's just listed twice
05:23 PM Tom_L: no big deal
05:26 PM JT-Cave: same error on the docs with the different switch
05:34 PM JT-Shop: https://repository.qtpyvcp.com/repo/linuxcnc_debs/jul/
05:34 PM JT-Shop: so TurBoss can build the docs... why can't we?
05:34 PM Tom_L: higher paygrade?
05:34 PM Tom_L: i'm about done with the install
05:35 PM Tom_L: then adding all the packages next
05:49 PM -!- #linuxcnc-devel mode set to +v by ChanServ
06:59 PM -!- #linuxcnc-devel mode set to +v by ChanServ
08:36 PM -!- #linuxcnc-devel mode set to +v by ChanServ
08:46 PM -!- #linuxcnc-devel mode set to +v by ChanServ