#linuxcnc-devel Logs

Jun 13 2017

03:25 AM Guest31857 is now known as Khetzal_
03:27 AM Khetzal_ is now known as Khetzal
08:01 AM jepler: .. I wonder if steptest shouldn't run in velocity mode ..
08:02 AM jepler: otoh sometimes it likes to think about position, nm
02:18 PM * TurBoss is back
02:18 PM TurBoss: seb_kuzminsky: where i can find the deb?
02:22 PM TurBoss: I found this : http://linuxcnc.org/dists/wheezy/
02:24 PM * TurBoss goes afk for a min
02:28 PM TurBoss: back
04:17 PM KimK_laptop: TurBoss: Thanks very much for helping. Until Seb gets back and can give you a better answer, why don't you have a look around at http://buildbot.linuxcnc.org/ and http://buildbot.linuxcnc.org/dev.html
04:17 PM TurBoss: sure thanks
04:17 PM TurBoss: now i'm a bit busy will have more time in 30 min
04:18 PM KimK_laptop: No problem, take your time.
04:18 PM TurBoss: :)
04:48 PM TurBoss: KimK_laptop: this should be what i'm looking for : http://buildbot.linuxcnc.org/dists/wheezy/scratch-rt/binary-i386/linuxcnc-dev_2.7.9~2.7.steptest.stop.after.jog~e35c177_i386.deb
04:49 PM KimK_laptop: OK, great. Happy hunting!
04:50 PM TurBoss: I can just run "dpkg -i packagename"?
04:50 PM TurBoss: to upgrade
04:52 PM TurBoss: o wrong link :D http://buildbot.linuxcnc.org/dists/wheezy/scratch-rt/binary-i386/linuxcnc_2.7.9~2.7.steptest.stop.after.jog~e35c177_i386.deb
04:52 PM TurBoss: this one is the right
04:52 PM TurBoss: hmmm rt or rtpreemtp
04:52 PM TurBoss: ?
04:53 PM TurBoss: y kernel is Linux lcnc 3.4-9-rtai-686-pae #1 SMP PREEMPT Debian 3.4.55-4linuxcnc i686 GNU/Linux
04:53 PM TurBoss: I should pick the rtpreemtp? seems so
04:54 PM KimK_laptop: Seems right to me too. How's rtpreempt been treating you? I think most are still using the classic RTAI.
04:54 PM TurBoss: very well
04:54 PM TurBoss: 7400 ns latency
04:54 PM TurBoss: on a old itx boar
04:54 PM TurBoss: d
04:55 PM TurBoss: what means uspace?
04:55 PM TurBoss: user space ?
04:56 PM TurBoss: then this is what i need : http://buildbot.linuxcnc.org/dists/wheezy/scratch-rtpreempt/binary-i386/linuxcnc-uspace_2.7.9~2.7.steptest.stop.after.jog~e35c177_i386.deb
04:56 PM TurBoss: not the other links :D
04:57 PM TurBoss: hmmm not sure ...
04:57 PM TurBoss: i'm confused
04:57 PM TurBoss: :D
06:00 PM pcw_mesa: TurBoss: you are using a RTAI kernel, so I don't think you want uspace
06:00 PM TurBoss: ok
06:00 PM TurBoss: ah god i'm blind
06:00 PM TurBoss: my eyeees
06:00 PM TurBoss: :D
06:00 PM TurBoss: just joking
06:00 PM TurBoss: thanks
06:00 PM pcw_mesa: the SMP PREEMPT is confusing
06:01 PM TurBoss: yes that was the only thing i saw
06:01 PM TurBoss: ok downloading the rtai one
06:07 PM TurBoss: ok the bug seems fixed
06:07 PM TurBoss: no magic steps
06:08 PM TurBoss: now downgrading
06:08 PM TurBoss: checking the bug again
06:08 PM TurBoss: and updating
06:33 PM TurBoss: Fixed \o/
06:33 PM TurBoss: Thanks
09:41 PM KGB-linuxcnc: 03Sebastian Kuzminsky 052.7 63a2eca 06linuxcnc 10src/hal/components/steptest.comp steptest: don't change position-cmd when not running * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=63a2eca
09:41 PM KGB-linuxcnc: 052.7-steptest-stop-after-jog e35c177 06linuxcnc 04. branch deleted * 14http://git.linuxcnc.org/?p=linuxcnc.git;a=commitdiff;h=e35c177
09:49 PM seb_kuzminsky: that should fix steptest better, without the "stop, then back up a little bit" bug in my first try at the fix
10:01 PM seb_kuzminsky: yay, tuesday night == hackspace night!