#hazzy Logs
Mar 06 2020
#hazzy Calendar
08:36 AM Lcvette: morning
10:57 AM TurBoss: hello
10:59 AM Lcvette: o/
10:59 AM Lcvette: hola turboss!
10:59 AM Lcvette: :D
11:00 AM TurBoss: hi @lcvette:matrix.org
11:00 AM Lcvette: lcvette just finished his work for the day and is getting ready to put the machine back together to test
11:01 AM Lcvette: did you play with your servo annymore?
11:10 AM TurBoss: a little bit
11:11 AM Lcvette: any more success?
11:11 AM TurBoss: kind of
11:13 AM Lcvette: \o/
11:13 AM Lcvette: kind of is better then none
11:13 AM Lcvette: :D
11:13 AM Lcvette: what made it better?
11:13 AM Lcvette: playing with the scale or did you find some other method?
11:15 AM TurBoss: nono
11:17 AM Lcvette: ?
11:18 AM Lcvette: a little bit, kind of, nono
11:18 AM Lcvette: lol
11:18 AM Lcvette: lcvette cannot make out anything from those
11:18 AM Lcvette: turboss ^^^
11:18 AM Lcvette: :D
11:19 AM TurBoss1: ill send you the files
11:19 AM Lcvette: ok
11:21 AM * TurBoss posted a file: sim.rc.servo.2.7z (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/SQMSRAwTYRtQVtDBGbTdJBFQ >
11:24 AM Lcvette: ok have the hal open
11:25 AM Lcvette: looks like the 20hz version
11:25 AM Lcvette: worked better than the 10hz version?
11:28 AM TurBoss: yes
11:32 AM Lcvette: you tested the siggen thing too it looks like
11:32 AM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/BPOwKxJqsmXnuVchWcqLNctl >
11:33 AM Lcvette: did it oscillate the servo?
11:34 AM Lcvette: ok i will go finish reassembling the machine to test thing
11:34 AM Lcvette: :D
11:34 AM Lcvette: \o/
12:23 PM TurBoss: > did it oscillate the servo?
12:23 PM TurBoss: yes it did
01:05 PM Lcvette: \o/
01:05 PM * Lcvette uploaded an image: VectorImage_2020-03-06_015753.jpg (96KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/kYijdaDiPJrYSHvqMKjLNela >
01:07 PM Lcvette: Turboss, I got the machine back together!
01:19 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/vWxmfxKTLromiZLJOvWkkgAr >
01:20 PM Lcvette: do i need to do this line?
01:20 PM Lcvette: ```
01:20 PM Lcvette: loadrt hm2_eth board_ip="10.10.10.10" config=" num_encoders=5 num_pwmgens=0 num_stepgens=5 sserial_port_0=30000000"
01:22 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/aaGpVhOIDVnvCybCQcUZvwyM >
01:25 PM Lcvette: turboss is it possible to add the test widget to the Probe basic?
01:25 PM Lcvette: * turboss do i need to add the test widget to probe basic?
01:27 PM TurBoss: hey
01:27 PM Lcvette: o/
01:27 PM TurBoss: me is away
01:27 PM Lcvette: right now i just changed all the 5i25 to 7i92
01:28 PM Lcvette: ok
01:28 PM TurBoss: cool
01:28 PM TurBoss: back in a while
01:28 PM Lcvette: ok
01:36 PM dremeier[m]1: does the servo works as you want?
01:36 PM Lcvette: dunno yet
01:36 PM Lcvette: only turboss has done limited testing
01:36 PM Lcvette: i need to fix up the hal to work with my card
01:36 PM Lcvette: but im not sure how to change everything over and don't want to risk my machine going crazy
01:36 PM Lcvette: lol
01:37 PM dremeier[m]1: may I help you, I´m just working on hal a lot.
01:37 PM Lcvette: sure
01:38 PM dremeier[m]1: sim.rc.servo2.7 is the working hal from turboss, right?
01:39 PM * Lcvette posted a file: sim.rc.servo.2.7z (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/RvBujzboyFQuslPMhHsvYYQP >
01:39 PM dremeier[m]1: If you send me you al and ini I can try to merge
01:40 PM dremeier[m]1: * If you send me you hal and ini I can try to merge
01:41 PM Lcvette: sek
01:42 PM * Lcvette posted a file: XK7130_INCH.hal (15KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/FNXEEENNiJDKMzuWhmNadzKC >
01:42 PM * Lcvette posted a file: XK7130_INCH.ini (6KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/KroAcsWvNbcetnUHrIpJxois >
01:42 PM Lcvette: dremeier: ^^^
01:43 PM dremeier[m]1: ok will have a look, what values come from you gui?
01:44 PM Lcvette: currently none
01:44 PM Lcvette: this was just to test the servo movement using the test gui turboss made
01:44 PM Lcvette: it is in the zip file
01:45 PM Lcvette: just a slider
01:45 PM dremeier[m]1: I have it
01:46 PM Lcvette: but i will have a subroutine that sends a calculated angle to the hal ?
01:46 PM Lcvette: that will take the place of the slider
01:46 PM dremeier[m]1: sure with a motion.analog pin
01:47 PM Lcvette: yes
01:47 PM Lcvette: so i guess it will be M68
01:47 PM Lcvette: ?
01:47 PM dremeier[m]1: yes
01:48 PM Lcvette: ok i will work on that now
01:48 PM dremeier[m]1: M68 E'younumber' Q'youValue'
01:49 PM Lcvette: yup
01:53 PM dremeier[m]1: first you add in your time hal: source cannon.hal
01:53 PM dremeier[m]1: and : TWOPASS = on
01:54 PM Lcvette: ?
01:55 PM dremeier[m]1: * and in your INI under [HAL]: TWOPASS = on
01:55 PM dremeier[m]1: so we add a new file called cannon.hal
01:56 PM Lcvette: coolant_cannon
01:56 PM Lcvette: :D
01:56 PM Lcvette: coolant_cannon.hal
01:56 PM dremeier[m]1: so it is easy to work on it
01:56 PM dremeier[m]1: fine : coolant_cannon.hal
01:56 PM Lcvette: :D
01:56 PM Lcvette: \o/
01:57 PM dremeier[m]1: what will be the pwmgen out on your 7i92?
01:58 PM Lcvette: sek
01:59 PM Lcvette: 7i76 TB3 temrinal 3 step+
01:59 PM Lcvette: * 7i76 TB3 terminal 3 step+
01:59 PM dremeier[m]1: ok thx
02:00 PM * Lcvette uploaded an image: image.png (140KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/xqFmrnhcbwQmXQVOpCbHymhn >
02:00 PM Lcvette: dremeier: ^^^
02:00 PM dremeier[m]1: 👍️
02:06 PM dremeier[m]1: can you have a look in hal show to see the pwm pin available
02:06 PM Lcvette: not sure i follow
02:07 PM Lcvette: you mean look to get the pin number from within halshow?
02:07 PM dremeier[m]1: yes
02:07 PM Lcvette: ok sek
02:10 PM * Lcvette uploaded an image: Screenshot_2020-03-06_15-02-57.png (55KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/mTGcvZKHaWvqDUFxfMZhlRCR >
02:10 PM Lcvette: is this it?
02:10 PM Lcvette: i think step+ is pwmgen0 and dir+ is pwmgen1
02:11 PM dremeier[m]1: but this is on the 7i92
02:11 PM dremeier[m]1: you want the pin on the 7i76?
02:11 PM Lcvette: that where it is connected
02:12 PM dremeier[m]1: ok, so there is no 7i76 path on halshow?
02:12 PM Lcvette: to 7i76 tb3 terminal 3
02:12 PM dremeier[m]1: I´m not familiar with you setup, sorry
02:13 PM dremeier[m]1: so we take the pins in you screenshot
02:13 PM Lcvette: i have a 7i92 ethernet fpga that is connected to a 7i76 daughter card and 7i77 daughter card
02:14 PM dremeier[m]1: Ok i see 👍️
02:14 PM * Lcvette uploaded an image: Screenshot_2020-03-06_15-07-07.png (12KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/WzSrsjRJtjlQNfpBxDRuhseD >
02:14 PM Lcvette: but under the 7i76 tab is only /o
02:14 PM Lcvette: * but under the 7i76 tab is only io
02:15 PM Lcvette: * but under the 7i76 tab is only io
02:15 PM dremeier[m]1: ok, thx
02:15 PM Lcvette: i can find the pin for the axis 4 step direction
02:22 PM * dremeier[m]1 posted a file: coolant_cannon.hal (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/kfoTUICpqXFpcgVolcqTyVyn >
02:23 PM dremeier[m]1: the siggen is not used at the moment, I guess it is to let the cannon sweep later on?
02:24 PM dremeier[m]1: Lcvette: ^^
02:25 PM Lcvette: yes
02:26 PM Lcvette: im not sure how it works
02:26 PM Lcvette: i pictured having a check box to enable the sweep and a sweep amount
02:26 PM dremeier[m]1: withe the sweep we do it later, first we must have a movment from the servo
02:26 PM Lcvette: in angle degrees
02:26 PM Lcvette: ok
02:27 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/JnyYaRsLaaHSHMcPiExWfXCS >
02:27 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/hNdSDIsKFliEQCapcDEiLNuD >
02:27 PM dremeier[m]1: you are the hero of subroutines :-)
02:27 PM Lcvette: :D
02:28 PM Lcvette: you are the hero of hal
02:28 PM Lcvette: \o/
02:28 PM Lcvette: and turboss
02:28 PM Lcvette: :D
02:28 PM dremeier[m]1: haha, i do my best 🤣
02:28 PM dremeier[m]1: have you seen the hal file ^^
02:28 PM Lcvette: downloading now
02:30 PM dremeier[m]1: ```net scale-sig motion.analog−out−01 => scale.0.in # input degrees```
02:30 PM Lcvette: motion.analog−out−1
02:31 PM dremeier[m]1: :-)
02:31 PM Lcvette: * motion.analog−out−01
02:31 PM Lcvette: :D
02:31 PM Lcvette: \o/
02:31 PM dremeier[m]1: 01 because the syntax is NN
02:31 PM Lcvette: ok, i need to add one thing in the designer and then merge to new release to test
02:31 PM Lcvette: gotcha
02:32 PM Lcvette: always use a leading zero
02:32 PM Lcvette: o/ \o
02:32 PM Lcvette: high five
02:32 PM dremeier[m]1: I´m sure it will not start, as alway if I change something /o\
02:32 PM Lcvette: lol
02:33 PM Lcvette: is the pwmgen supposed to be 00?
02:33 PM Lcvette: for the first one?
02:33 PM * Lcvette uploaded an image: image.png (7KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/LLMrehjhZkwnOAZHndJXfujQ >
02:33 PM dremeier[m]1: you dont have any other pwmgen in your hal, so it must be the first one
02:33 PM Lcvette: the first one is 00 no?
02:33 PM dremeier[m]1: yes
02:34 PM Lcvette: oh i see
02:34 PM Lcvette: you called 00
02:34 PM Lcvette: but named it pwmgen1
02:34 PM Lcvette: # enable 7i92 pwmgen1
02:34 PM Lcvette: setp hm2_7i92.0.pwmgen.00.enable 1
02:34 PM dremeier[m]1: sorry:
02:34 PM dremeier[m]1: net scale-pwm scale.0.out => hm2_7i92.0.pwmgen.00.value
02:35 PM dremeier[m]1: 00 is correct
02:35 PM Lcvette: * ```
02:35 PM Lcvette: # enable 7i92 pwmgen1
02:35 PM Lcvette: setp hm2_7i92.0.pwmgen.00.enable 1
02:35 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/GoKIrAsxaLXxVdeVujjFTKOP >
02:35 PM Lcvette: ok fixed in hal
02:37 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/PeniRLpDiQbAgqzuzmtOqxuY >
02:38 PM dremeier[m]1: look ok for me
02:52 PM Lcvette: what do i do to the ini?
02:53 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/XiyjRtTiXThZrmkngzcWkAhm >
02:53 PM Lcvette: dremeier: ^^^
02:53 PM Lcvette: like this?
02:55 PM dremeier[m]1: yes you can do that like this, but If you have buttons or values from qtpyvcp-screen then it must called from the postgui_halfile
02:55 PM Lcvette: ok
02:55 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/oeMNtGyDjhbxQIqmePwVGMVi >
02:56 PM Lcvette: what you said about twopass on?
02:56 PM dremeier[m]1: no
02:56 PM dremeier[m]1: sek
02:56 PM Lcvette: dremeier (@dremeier:matrix.org)
02:56 PM Lcvette: first you add in your time hal: source cannon.hal
02:56 PM Lcvette: and in your INI under [HAL]: TWOPASS = on
02:56 PM Lcvette: i don't understand this
02:57 PM dremeier[m]1: yes the you have it called from postgui_halfile
02:57 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/yBnCpGhmhhcgOauvKmgtQgoO >
02:57 PM dremeier[m]1: the TWOPASS=on is nice to have, so you can have multiple loadrt´s
02:58 PM Lcvette: like that ^^^
02:58 PM dremeier[m]1: nope
02:58 PM Lcvette: /o\
02:58 PM dremeier[m]1: mom
02:58 PM Lcvette: k
02:58 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/JKyZdqVYYLMHfTGfEKsQumnB >
02:59 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/MFWXMphwzmqZEeQVnkoCaDfZ >
02:59 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/VWCoxeBGMuCJxzpeenuyLXdF >
02:59 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/OHpAFQOLRAyWMpVpFVJkJGSu >
03:00 PM dremeier[m]1: and in yout time.hal add
03:00 PM dremeier[m]1: source hallib/coolant_cannon.hal
03:00 PM dremeier[m]1: do not call the coolant_cannon.hal from your ini
03:04 PM dremeier[m]1: If you want it easy and don´t need buttons or values from your gui, then you can call coolant_cannon.hal from your ini
03:04 PM Lcvette: can you show me
03:04 PM Lcvette: i don't understand you instructions
03:05 PM dremeier[m]1: first question, do you plan buttons or values from your gui to use in the coolant_cannon.hal?
03:05 PM Lcvette: yes
03:05 PM dremeier[m]1: ok then:
03:06 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/epDaHichbEmAnhZcQnRCtmec >
03:06 PM Lcvette: ok
03:06 PM dremeier[m]1: edit your time.hal
03:06 PM Lcvette: when does the coolant cannon hal load?
03:07 PM dremeier[m]1: ^^
03:07 PM dremeier[m]1: source hallib/coolant_cannon.hal
03:07 PM Lcvette: you are going to have to show me
03:07 PM Lcvette: lol
03:07 PM Lcvette: sorry
03:07 PM dremeier[m]1: lol
03:07 PM Lcvette: i cannot see what you are picturing
03:07 PM dremeier[m]1: open your time.hal
03:08 PM dremeier[m]1: moment stop
03:08 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/mtUZlXHhaZQynxwEiQecXanO >
03:09 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/qozDpPxUVbwIoMryoCUqDPKI >
03:09 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/foNjvpOiIoCQYXCjFBQoFFsH >
03:10 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/qgHesMMbYYvpzLzSpgEUsKlo >
03:10 PM dremeier[m]1: 👍️
03:10 PM dremeier[m]1: \o/
03:11 PM Lcvette: failed to laod
03:11 PM dremeier[m]1: ```` test one two :-) ````
03:11 PM dremeier[m]1: debug?
03:11 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/yOGCYhuNhroERpPhFiEQUQtF >
03:14 PM dremeier[m]1: found the mistake, one moment pls
03:16 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/GGHGaaRtaMtfkhApMGLIkyPQ >
03:17 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/IXdAQRHzWoXeHCmtSNrzmBlv >
03:17 PM * dremeier[m]1 sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/TfJtqdkqNKHUDjUKJjlNwXHe >
03:18 PM * dremeier[m]1 posted a file: coolant_cannon.hal (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/EWHsXJSyUcUHfmxyRLzdrNYv >
03:18 PM Lcvette: scale.servo.in
03:19 PM dremeier[m]1: I don´t know why I cant put in the text from the file? dam
03:19 PM dremeier[m]1: you see the file^^
03:20 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/emAyslkmaSWzgXEIdlZLYuvM >
03:20 PM dremeier[m]1: how do you do that ^^
03:20 PM Lcvette: pwm_frequency 333 is right?
03:22 PM dremeier[m]1: that I don´t know, copied from turboss file is 20
03:22 PM Lcvette: turboss was using 20hz
03:22 PM Lcvette: i will be using 333hz
03:22 PM Lcvette: so i know how to change the scale and gain
03:23 PM Lcvette: but wasn't sure if that 20 was hz
03:23 PM dremeier[m]1: ok fine
03:23 PM Lcvette: im guessing that is the frequency set
03:23 PM dremeier[m]1: yes is hz
03:23 PM Lcvette: base frequency
03:23 PM Lcvette: ok so 333 is correct
03:23 PM Lcvette: great!
03:23 PM Lcvette: :D
03:24 PM Lcvette: how do i get rid of dos line endings?
03:24 PM dremeier[m]1: just in case the servo is not turning correct, can it turn free?
03:24 PM Lcvette: also still failed to load postgui hal fine
03:25 PM Lcvette: i think so
03:25 PM dremeier[m]1: <Lcvette "how do i get rid of dos line end"> what do you mean? what editor do you use?
03:25 PM Lcvette: sublime
03:25 PM Lcvette: are you on windows?
03:26 PM Lcvette: its ok i will just remake the file real quick
03:26 PM dremeier[m]1: yes, but using notepad++, which also has no dos ends
03:26 PM Lcvette: its short
03:26 PM Lcvette: that will induce dos line endings
03:26 PM Lcvette: when i use notepad++ it always has dos line endings
03:27 PM dremeier[m]1: silly Windows
03:27 PM Lcvette: :D
03:27 PM Lcvette: silly windows
03:27 PM Lcvette: lol
03:27 PM dremeier[m]1: if you have a debug show me
03:34 PM TurBoss: yo is back
03:34 PM TurBoss: hey dremeier !
03:34 PM dremeier[m]1: hola TurBoss
03:35 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/ApkPNCetDmFMtMcUnfGtcwqk >
03:35 PM dremeier[m]1: we just transfer you servo.hal to lcvette
03:35 PM Lcvette: dos line endings fixed but still won't load
03:35 PM dremeier[m]1: what does the debug say?
03:37 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/BqnNRwoxAWUtgOweraJAOqoh >
03:37 PM Lcvette: sorry pasted wrong thing above now check above
03:37 PM Lcvette: its the temrinal errors
03:37 PM Lcvette: dremeier: ^^^
03:39 PM TurBoss: you allready have a scale loaded in yor main hal file
03:39 PM TurBoss: may need to be tweaked
03:39 PM TurBoss: loadrt scale count=2
03:39 PM Lcvette: hi turboss o/
03:39 PM Lcvette: where?
03:40 PM Lcvette: in the coollant cannon hal?
03:40 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/EJduELwFxnWLkaJdiXOQnrZu >
03:40 PM TurBoss: scale.0.
03:40 PM TurBoss: scale.1.
03:40 PM TurBoss: he Lcvette
03:40 PM TurBoss: oki
03:40 PM dremeier[m]1: > <@TurBoss:matrix.org> scale.0.
03:40 PM dremeier[m]1: > scale.1.
03:40 PM dremeier[m]1: not working by lcvette
03:41 PM dremeier[m]1: because he has already loaded scal in main hal with names
03:41 PM dremeier[m]1: so we switch on TWOPASS
03:41 PM dremeier[m]1: and add a ne name in cannon.hal
03:42 PM dremeier[m]1: * and add a new name in cannon.hal
03:42 PM dremeier[m]1: * because he has already loaded scale in main hal with names
03:42 PM TurBoss: did the slider move at all?
03:43 PM dremeier[m]1: we skip the slider and have a motion-analog pin
03:43 PM Lcvette: i did not test the slider
03:46 PM Lcvette: dremeier: did you see the temrinal error messege?
03:46 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/jrzFinXPswaEjknTMonCvzbV >
03:49 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/EjVVeOTjYLbCzqrDKbezEgTa >
03:49 PM dremeier[m]1: Lcvette: you are on SIM???
03:49 PM Lcvette: thats the main hal, it loads a spindle scale
03:49 PM TurBoss: @lcvette you have other scale comp i
03:49 PM Lcvette: yes on sim
03:50 PM Lcvette: maybe why 7i92 isn't loading
03:50 PM Lcvette: ?
03:50 PM dremeier[m]1: how can it work on sim?? that I don´t understand
03:50 PM Lcvette: /o\
03:50 PM Lcvette: i dunno
03:51 PM TurBoss: me moves to dev
03:51 PM Lcvette: i guess i need to merge programmable coolant to master and test on machine
03:51 PM Lcvette: ?
03:51 PM dremeier[m]1: if you load a hardware pin on sim, that can´t work
03:51 PM TurBoss: wait
03:51 PM TurBoss: true^^
03:51 PM TurBoss: but it complains about scale
03:52 PM dremeier[m]1: yes, I guess that the twopass does not work on postgui_call files
03:52 PM dremeier[m]1: so we have to add the scal in main hal
03:53 PM dremeier[m]1: ````loadrt scale names=scale.spindle,scale.servo````
03:53 PM dremeier[m]1: change this in you main hal ^^ Lcvette
03:53 PM dremeier[m]1: and delet the line in cannon.hal
03:53 PM dremeier[m]1: * and delete the line in cannon.hal
03:55 PM Lcvette: ok
03:56 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/BbgBODTukVdbBlQjCRrEgMFR >
03:56 PM Lcvette: dremeier: ^^^
03:57 PM dremeier[m]1: ````addf scale.servo servo-thread````
03:57 PM dremeier[m]1: to main hal
03:57 PM dremeier[m]1: delete in cannon.hal
03:58 PM Lcvette: wait
03:58 PM Lcvette: im still on sim
03:58 PM Lcvette: so it is not loading the main hal file
03:59 PM dremeier[m]1: thast is all very confusion with you sim files and you gave me the real files, that is hard
03:59 PM Lcvette: i added the scale.servo to the sim file
04:00 PM Lcvette: now is barking about 7i92 lines because they are not there
04:00 PM Lcvette: so i thinik this needs to be tested on the machine maybe
04:00 PM dremeier[m]1: sure, all other makes no sense
04:01 PM Lcvette: but that means i cannot test anything in sim
04:01 PM Lcvette: /o\
04:01 PM Lcvette: we probably need to amke one in sim too
04:01 PM Lcvette: turboss didn't you do one in software>?
04:01 PM TurBoss: yes
04:02 PM Lcvette: can you setup the probe basic sim config to work with it in the programmable coolant branch?
04:02 PM Lcvette: it is all setup to test now
04:02 PM Lcvette: and could use the halscope to verify?
04:02 PM TurBoss: ok
04:02 PM TurBoss: yes
04:02 PM Lcvette: ok great, i think that is the first place to test so i can test the subroutine connections and stuff
04:05 PM TurBoss: http://linuxcnc.org/docs/html/man/man9/pwmgen.9.html
04:08 PM TurBoss: Lcvette: do you have more pwmgen?
04:08 PM TurBoss: maybe for the spindle?
04:08 PM * Lcvette posted a file: XK7130_INCH(1).hal (15KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/AwTbjLqTTDCsuKBuwSTnKUUd >
04:08 PM Lcvette: that is the machine hal
04:09 PM Lcvette: i added the thing for the seervo
04:09 PM Lcvette: scale.servo to the same line as the spindlescal
04:09 PM Lcvette: * scale.servo to the same line as the spindle scale
04:09 PM Lcvette: loadrt scale names=scale.spindle,scale.servo
04:10 PM TurBoss: ok
04:10 PM Lcvette: but untested on machine
04:10 PM TurBoss: my be a good idea to add ``` count=2```
04:10 PM TurBoss: onthat line too
04:10 PM Lcvette: where to add?
04:10 PM Lcvette: end?
04:10 PM TurBoss: ``` loadrt scale count=2 names=scale.spindle,scale.servo
04:10 PM Lcvette: ```
04:10 PM Lcvette: loadrt scale names=scale.spindle,scale.servo,count=2
04:10 PM Lcvette: ?
04:10 PM TurBoss: yes
04:11 PM TurBoss: no coma
04:11 PM Lcvette: ```
04:11 PM Lcvette: loadrt scale names=scale.spindle,scale.servo count=2
04:11 PM TurBoss: yes
04:11 PM Lcvette: ok
04:11 PM TurBoss: ok pwmgens
04:11 PM dremeier[m]1: what??? names and count????
04:12 PM dremeier[m]1: cant work
04:12 PM TurBoss: oh
04:12 PM Lcvette: /o\
04:12 PM Lcvette: lol
04:12 PM Lcvette: remove count?
04:12 PM TurBoss: if names just works then is ok
04:14 PM dremeier[m]1: either you use names or count
04:14 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/MwisIGDfNZXKGGKKyDFblxEV >
04:14 PM TurBoss: ohhhhkay
04:15 PM Lcvette: thats the other scale stuff i see in the machine hal
04:16 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/KRXmzJEkUbpdQeohZadMFVFB >
04:19 PM dremeier[m]1: that has nothing to do with the loadrt scal, this is the near tread
04:19 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/BMULDmUSGuYiIkvIcsyTiNct >
04:20 PM TurBoss: and
04:20 PM TurBoss: ```
04:20 PM TurBoss: net pwm-sig pwmgen.0.value <= scale.servo.out
04:23 PM dremeier[m]1: that is the sowtware pwmgen, you don´t whant to use the hardware pwmgen?
04:23 PM TurBoss: on sim
04:23 PM dremeier[m]1: ah, sorry you are on sim now! - sorry
04:23 PM Lcvette: yes need to test on sim
04:23 PM Lcvette: make sure all is working
04:24 PM dremeier[m]1: what a confusing story, lol /o\
04:24 PM Lcvette: then merge to master and make a release and test on machine
04:24 PM TurBoss: no
04:24 PM Lcvette: i forgot about the 7i92 stuff not working on sim
04:24 PM Lcvette: /o\
04:24 PM TurBoss: whay a mess
04:24 PM TurBoss: :P
04:24 PM TurBoss: ah ok
04:24 PM Lcvette: is a mess
04:24 PM TurBoss: you wan't a functional sim
04:25 PM Lcvette: yes
04:25 PM Lcvette: for testing the subroutines and stuff
04:25 PM TurBoss: ok if you added thoose lines
04:25 PM Lcvette: much easier to work on subs at dev then on vertical keyvboard on machine panel
04:25 PM Lcvette: where turboss?
04:25 PM TurBoss: to the servo.hal
04:26 PM TurBoss: you can have the ini load hm2_rc_servo.hal or sim_rc_servo.hal
04:26 PM Lcvette: can you supply the whole hal;
04:26 PM TurBoss: you first
04:27 PM Lcvette: i don't know where or what hal
04:27 PM TurBoss: show
04:27 PM * Lcvette posted a file: coolant_cannon.hal (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/XWvlrxBTtaBboznZZRSgmpmB >
04:27 PM Lcvette: this was the hal dremeier made
04:27 PM Lcvette: but is for the 7i92
04:27 PM TurBoss: ok
04:27 PM TurBoss: I'll made the sim_cannon.hal
04:28 PM Lcvette: ok
04:28 PM Lcvette: \o/
04:29 PM dremeier[m]1: sorry, I'm out. I'm getting headache 🤣
04:29 PM * TurBoss posted a file: sim_cannon.hal (1KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/XnxAapbPqZuXFaVMbyhjCXxF >
04:29 PM TurBoss: untested
04:30 PM TurBoss: just remove this line
04:30 PM TurBoss: ```
04:30 PM TurBoss: loadrt scale names=scale.servo
04:30 PM TurBoss: since you allready have it on the main hal
04:33 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/siMHTLtgaQXpRdIQRkNlqeWT >
04:34 PM TurBoss: clean file
04:35 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/GcUDDhzMJPIUfpMxGdTNtEFi >
04:35 PM TurBoss: ops
04:36 PM TurBoss: ``` loadrt pwmgen output_type=0
04:37 PM TurBoss: * ```
04:37 PM TurBoss: loadrt pwmgen output_type=0
04:37 PM TurBoss: ```
04:37 PM Lcvette: am i suppost to still load the sim_cannon.hal file from within the time.hal file?
04:37 PM TurBoss: how is that?
04:37 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/zwkoVpucaLAdNxiHsmuGwxuL >
04:38 PM TurBoss: just add a line in you [HAL] section
04:38 PM Lcvette: this is what dremeier said
04:38 PM Lcvette: he said that no good
04:38 PM TurBoss: oh ok
04:38 PM Lcvette: but i dunno
04:38 PM TurBoss: should be ok
04:38 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/OzGmLLvIbJnYKqyCLctiulmm >
04:38 PM TurBoss: yes
04:38 PM Lcvette: like this added the loadrt line
04:39 PM TurBoss: remove the first line
04:39 PM TurBoss: so only one loadrt pwmgen remains
04:39 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/tEjaZkmbdPmZmTkwtCJKTNaf >
04:39 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/DGwAfUSndcVjaivFOUXDNvUc >
04:40 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/kICCvpaJYvfDGQBQvqIQtyzp >
04:40 PM TurBoss: repeat
04:40 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/ZaJDXsXdYjoWYkBagCwRpHlw >
04:40 PM TurBoss: Lcvette: notice that I removed first line
04:41 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/HiKOGzNKwFOdRQWEwHtQZKzJ >
04:41 PM Lcvette: yes this is with your new one i jujst ran
04:41 PM TurBoss: ok
04:41 PM TurBoss: new error
04:41 PM Lcvette: getting smaller
04:41 PM Lcvette: \o/
04:41 PM Lcvette: :D
04:42 PM TurBoss: ```
04:42 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/mpSLNQQUZGagMTXcGhIFdkgt >
04:42 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/uJiHonnJcuQfJNViOvWkjvZR >
04:43 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/CLSdpJgakzpgfItpkYJapRMQ >
04:43 PM TurBoss: Lcvette: ^^
04:43 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/ooqgAtixkHwcURabxCPNhgGa >
04:44 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/PcWJiEIZkeULNGhLgOqgihGZ >
04:44 PM TurBoss: Edited ^^
04:44 PM Lcvette: that is the edited one
04:44 PM Lcvette: im fast l;ike lightening
04:44 PM Lcvette: :o
04:44 PM Lcvette: \o-
04:44 PM TurBoss: -o/
04:44 PM Lcvette: lol
04:44 PM Lcvette: :D
04:44 PM TurBoss: was edited twice
04:44 PM TurBoss: check latest
04:45 PM TurBoss: phew
04:45 PM TurBoss: pwm-freq not pwm_freq
04:45 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/VfDLsUOksoChZqWDQJvUVjoW >
04:45 PM TurBoss: Lcvette:
04:45 PM Lcvette: same error
04:45 PM Lcvette: i used the edited one
04:45 PM TurBoss: pwm-freq not pwm_freq
04:46 PM TurBoss: line 8
04:46 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/RykhJnLFEOhYvtpkUxYdAesH >
04:46 PM TurBoss: phew!
04:46 PM Lcvette: lol
04:47 PM TurBoss: pwmgen.0.pwm-freq
04:47 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/DOYqpAGyFarPGKViYhjptbdK >
04:48 PM TurBoss: you need to add 333
04:48 PM TurBoss: to the end of the line
04:48 PM TurBoss: to setup the output frequency
04:49 PM TurBoss: ```
04:49 PM TurBoss: setp pwmgen.0.pwm_freq 333
04:50 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/gNAbQLGJGAZTRLscKHVrfguq >
04:50 PM TurBoss: hurray!
04:50 PM Lcvette: hahaha amalog
04:50 PM TurBoss: did you extend max_aoi?
04:50 PM Lcvette: :D
04:50 PM TurBoss: oh didn't notice
04:51 PM Lcvette: \o/
04:51 PM Lcvette: loaded!
04:51 PM Lcvette: HURRAY!!
04:51 PM TurBoss: great!
04:51 PM Lcvette: :D
04:51 PM TurBoss: \o/
04:51 PM TurBoss: now fire halscope
04:51 PM Lcvette: this is why its easier to do on dev first with sim
04:51 PM Lcvette: that would have taken me 3 hours on the machine
04:52 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/ONSaLwBIaHKUnCunkpIKrTec >
04:52 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/NIBfayaPZVGuinaWvngURSJo >
04:53 PM Lcvette: ive been getting this with the coolant subroutine
04:53 PM Lcvette: im not sure what or where it is coming from
04:53 PM Lcvette: any idea?
04:53 PM TurBoss: a sum?
04:53 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/bvBuyIARccDAHRnRClxrfYTg >
04:53 PM Lcvette: this is the subroutine that is called
04:53 PM Lcvette: but the equations seem correct
04:53 PM TurBoss: ```
04:53 PM TurBoss: [[#<vertical_spindle_nozzle_dist>] + [#<pc_tool_length>]]
04:54 PM Lcvette: ive used them in the past with no incident
04:54 PM TurBoss: * ```
04:54 PM TurBoss: [#<vertical_spindle_nozzle_dist> + #<pc_tool_length>]
04:54 PM TurBoss: ```
04:54 PM Lcvette: k testing
04:58 PM TurBoss: ```
04:58 PM TurBoss: #<coolant_abs_angle> = [ATAN[#<tool_tip_position>] / [#<horizontal_spindle_nozzle_dist>]]
04:58 PM TurBoss: any succes Lcvette ??
04:59 PM Lcvette: \o/
05:00 PM Lcvette: what channel do i log with the scope?
05:01 PM Lcvette: TurBoss: ^^^
05:02 PM * Lcvette uploaded an image: Screenshot_2020-03-06_17-54-53.png (37KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/UTGSXMatnqFPLXvshjtWwGSi >
05:03 PM TurBoss: pwmgen.0
05:03 PM TurBoss: i think is pwmgen.0.pwm
05:05 PM * Lcvette uploaded an image: Screenshot_2020-03-06_17-58-20.png (57KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/llmtmZBcVmhqiHkxEnxorTDe >
05:06 PM TurBoss: ok let me try on sim
05:06 PM TurBoss: not ok
05:06 PM Lcvette: dunno doesn't seem to change with tool changes
05:08 PM TurBoss: are you uing m66 to update the value?
05:08 PM Lcvette: ?
05:08 PM Lcvette: it is updating
05:09 PM Lcvette: i can see the agle change in the box and everything
05:09 PM Lcvette: i found a better way than the m66
05:09 PM Lcvette: it just needed to run through a internal if statement and it resolved that issue
05:11 PM Lcvette: TurBoss: ^^^
05:11 PM Lcvette: sek i will push the latest
05:12 PM * JT[m] uploaded an image: VectorImage_2020-03-06_050505.jpg (136KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/otUDrzinprMGNHsoKufeoYhY >
05:15 PM Lcvette: jt got a vette?
05:17 PM Lcvette: TurBoss: i pushed the latest with everything on kraken
05:17 PM * TurBoss got visit
05:17 PM Lcvette: maybe you can figure the pwmgen thing?
05:17 PM Lcvette: ok
05:17 PM TurBoss: latter
05:18 PM JT[m]: Aye bought it today
05:24 PM Lcvette: fantastic!
05:24 PM Lcvette: manual or auto?
05:25 PM Lcvette: graham forgot to measure how far in the viser the stock and deepest cut would be
05:26 PM jthornton: 6 speed
05:27 PM Lcvette: nice!
05:27 PM Lcvette: any mods or all stopck?
05:27 PM Lcvette: * any mods or all stock?
05:29 PM * JT[m] uploaded an image: VectorImage_2020-03-06_052203.jpg (40KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/GRQfjPGvSkEuuCMcYfvBdYyM >
05:30 PM Lcvette: Where's the rest of those tips?
05:30 PM JT[m]: Dunno, what else is supposed to be there
05:30 PM Lcvette: Does it have long tube headers or just a catback
05:32 PM JT[m]: I'll look in a bit, gotta get the Spyder in
05:32 PM Lcvette: K
05:42 PM * JT[m] uploaded an image: VectorImage_2020-03-06_053444.jpg (24KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/lyETwrODyHeaVhsdbqYvPtNu >
05:42 PM JT[m]: Looks like ordinary cast iron exhaust
05:42 PM Lcvette: ah
05:42 PM Lcvette: cold air intake?
05:43 PM * JT[m] uploaded an image: VectorImage_2020-03-06_053617.jpg (37KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/WeZthDwZAHVuYkVrGAKItpHs >
05:45 PM JT-Shop: https://www.corvetteblogger.com/2015/03/14/collectible-corvettes-2004-corvette-z06-commemorative-edition/
05:45 PM JT-Shop: it's that one
05:47 PM Lcvette: z06?
05:47 PM dremeier[m]1: Lcvette: short question, do you know how to reset the Notifications in the notificationwidget from hal. I mean is there a hal pin I can use to reset? In axis is the 'axisui.notifications-clear' pin. but I can´t find a pin for qtpyvcp.
05:47 PM dremeier[m]1: btw. nice Car!
05:48 PM Lcvette: dremeier: not sure about hal pin to dismiss notification
05:48 PM Lcvette: JT-Shop: i don't think that is a z06 unless they changed the fuel rail covers
05:48 PM Lcvette: they are normall red from the factory
05:49 PM Lcvette: but the z06 is pretty sweet
05:49 PM dremeier[m]1: will ask turboss or hazzy, later on, thx
05:49 PM Lcvette: those cars with long tubes, catback, cold air intake and a tune usually make about 385rwhp
05:49 PM Lcvette: dremeier: sorry im not hal competent
05:50 PM Lcvette: /o\
05:50 PM dremeier[m]1: lol, but sub and gui 👍️
05:51 PM Lcvette: yes
05:51 PM Lcvette: those i can help with usually
05:51 PM Lcvette: hal...ppppllllltttthhhh nothing
05:53 PM JT[m]: Would it have a z06 emblem?
05:54 PM Lcvette: yes but can also add those as they sell them aftermarket
05:54 PM Lcvette: kind silly too
05:54 PM Lcvette: but some people would do it to the fixed roof non z06 models
05:55 PM Lcvette: all z06's were fixed roof coupes
05:55 PM Lcvette: and had brake air vents
05:56 PM * Lcvette uploaded an image: image.png (202KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/qxDWfREqVoNMziaJTCCpWRkA >
05:57 PM Lcvette: those wheels are z06 specific, the rear brake vents are z06 specific, the emblem, and it being a FRC (fixed roof coupe)
05:58 PM * Lcvette uploaded an image: image.png (79KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/UnYOmAWJJFRnSKgjqEDMEayo >
05:59 PM Lcvette: front car is a fixed roof coupe last car is standard coupe
05:59 PM Lcvette: JT: ^^^
05:59 PM Lcvette: notice the fron FRC car does not have brake vents in front of the rear wheels
06:00 PM * JT[m] uploaded an image: VectorImage_2020-03-06_055257.jpg (28KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/qVlBfBLhawWTRDaTyswAJEzC >
06:00 PM * JT[m] uploaded an image: VectorImage_2020-03-06_055310.jpg (34KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/SyTrrIaDPNaobOsFYbSzNoDh >
06:00 PM Lcvette: yeah thats a standard ls1 vette
06:00 PM Lcvette: nothing wrong with it
06:00 PM Lcvette: i like the standard coupe bodys better personally
06:01 PM JT[m]: Yea I don't care for the hood stripes
06:02 PM Lcvette: me either
06:03 PM Lcvette: https://www.eastcoastsupercharging.com/supercharger-systems/1997-04-corvette-ls1-ls6_132/ecs-novi-1500-2200-supercharger-kit-corvette-ls1-ls6-c5-97-04-detail
06:03 PM Lcvette: this is what you need now!
06:03 PM JT[m]: How do you get the front cover off to mount a license plate?
06:05 PM Lcvette: not sure, we dont have front plates here
06:17 PM JT[m]: Two tiny Phillips screws
07:04 PM roguish[m]: yeah, and we have a virus cruise ship about to dock.....
07:05 PM roguish[m]: floating peatry dishes....
07:05 PM roguish[m]: just like airplanes....filthy, disgusting.
07:07 PM roguish[m]: and Trumpass with diarrhea of the mouth again. now on about the virus....
07:21 PM hazzy-m: Hello
07:22 PM * hazzy-m is unsuccessfully trying to convert a white iPhone 11 into a black one
07:23 PM hazzy-m: Supposedly black models won't be back in stock for a few months at least because of the Kung Flu
07:25 PM hazzy-m: So I'm stuck with a constantly dirty looking white one lol
07:34 PM roguish[m]: try a rattle can paint job...
07:36 PM roguish[m]: here's a good one.... https://www.nationalgeographic.com/science/2020/01/how-coronavirus-spreads-on-a-plane/
08:21 PM hazzy-m: We're no longer servicing machines in China or Italy because of the corona virus
08:52 PM Lcvette: Can't blame ya there
08:54 PM Lcvette: Hazzy i have a word thing happening with a subroutine calc, it looks like it should be pretty simple and basic but I'm getting really weird results i can't explain
08:55 PM Lcvette: If you have 2 minutes you probably could punt out what is going on that I'm missing
09:01 PM Lcvette: The i issue is when i add am offset for the coolant nozzle angle, it should just add the degree entry in the line edit to the calculated angle, but for some reason the sim is way out of wack from what you would expect
09:02 PM Lcvette: For instance i think tool 3 base angle calculated is 41.186 degrees when i add 1 degree offset, the calculated value comes to 45.000???
09:03 PM Lcvette: And 2 degree offset the sum is 48.336...... so something is really weird
09:27 PM Lcvette: * Hazzy i have a weird thing happening with a subroutine calc, it looks like it should be pretty simple and basic but I'm getting really weird results i can't explain
10:21 PM Lcvette: o/
10:30 PM TurBoss: o/
10:30 PM Lcvette: i figured my problem
10:30 PM Lcvette: \o/
10:31 PM TurBoss: yes?
10:31 PM TurBoss: hurray!
10:31 PM Lcvette: was the order i brought in the offset value
10:32 PM Lcvette: works now!
10:32 PM Lcvette: \o/
10:32 PM TurBoss: ok so we can figure the pwm stuff
10:33 PM Lcvette: yes that would be great!
10:33 PM Not: [02probe_basic] 07Lcvette pushed 031 commit to 03programmable_coolant [+0/-0/±8] 13https://git.io/JvwQ0
10:33 PM Not: [02probe_basic] 07Lcvette 03a0b1a13 - fixed offset value and other tool change subs for cannon angle
10:33 PM hazzy-m: Hurray!!
10:33 PM Lcvette: everything in the subs is now working correctly
10:34 PM hazzy-m: Lcvette fued it
10:34 PM Lcvette: just need the pwm
10:34 PM Lcvette: hurray!
10:34 PM Lcvette: \o/
10:34 PM TurBoss: fu!
10:34 PM TurBoss: fuet
10:34 PM Lcvette: pushed the latest
10:42 PM * Lcvette posted a file: programmable_coolant.mkv (1418KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/JpoMTamhjLkwvGXExZTfxFsV >
10:42 PM Lcvette: \o/
10:43 PM Lcvette: works with positive and negative offsets and i made the entry persistent
10:43 PM Lcvette: so all good here!
10:46 PM Lcvette: turboss i checked the aio count and it is set at 64
10:46 PM Lcvette: so should be good
10:47 PM Lcvette: ive been testing different channels but the only one that makes a waveform is the one yuo said
10:47 PM Lcvette: and sometimes the halscope locks up
10:48 PM Lcvette: hazzy: \o/
10:48 PM Lcvette: you snuck in!
10:48 PM Lcvette: o/
10:48 PM Lcvette: do you know pwm stuff?
10:48 PM Lcvette: :o
10:51 PM Lcvette: the one you said to try is now changing with a tool change
11:00 PM * Lcvette uploaded an image: Screenshot_2020-03-06_23-53-01.png (107KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/oDhbmAhQCzbolwrWMlRYgqSd >
11:01 PM * Lcvette uploaded an image: Screenshot_2020-03-06_23-54-04.png (107KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/iIcMxhJEaAoYNeEXEAlsMYye >
11:01 PM Lcvette: TurBoss: turboss is this right?
11:02 PM TurBoss: nope
11:02 PM Lcvette: thats for no tool and a large tool to show a difference
11:02 PM Lcvette: /o\
11:02 PM TurBoss: don't worry I'm on dev
11:02 PM TurBoss: lol
11:02 PM Lcvette: ok
11:02 PM TurBoss: /ø\
11:15 PM Lcvette: what is addf?
11:21 PM TurBoss: add function
11:21 PM Lcvette: i found in hal basics
11:21 PM Lcvette: still makes no sense to me
11:21 PM TurBoss: it adds the loaded module to the desired thread
11:21 PM Lcvette: i need pop up books for hal
11:21 PM Lcvette: lol
11:22 PM Lcvette: opne day hal will magically make sense to me
11:22 PM Lcvette: * one day hal will magically make sense to me
11:23 PM Lcvette: whats make-pulses
11:23 PM Lcvette: lol
11:23 PM Lcvette: is that a real thing?or you made it up?
11:23 PM TurBoss: http://linuxcnc.org/docs/devel/html/man/man9/pwmgen.9.html
11:28 PM Lcvette: type 0: single output
11:28 PM Lcvette: do we need this?
11:28 PM Lcvette: to tell it that it is only single output pin?
11:28 PM Lcvette: based on input value?
11:29 PM Lcvette: turboss ^^^
11:29 PM TurBoss: i think that yes
11:29 PM Lcvette: where is it defined?
11:30 PM TurBoss: loadrt pwmgen output_type=0
11:30 PM Lcvette: ah ok
11:31 PM TurBoss: I think I found
11:31 PM Lcvette: im beginning to see somethings
11:31 PM Lcvette: yes?
11:31 PM Lcvette: \o/
11:31 PM TurBoss: pwm-freq is not begin stored
11:31 PM Lcvette: /o\
11:31 PM TurBoss: can you run sim=
11:31 PM Lcvette: yes
11:31 PM TurBoss: and run halscope and all that
11:31 PM Lcvette: tell me what to change
11:31 PM Lcvette: or test
11:31 PM Lcvette: yes
11:31 PM TurBoss: the run halshow
11:32 PM Lcvette: i have everythign open
11:32 PM Lcvette: what channel for halscope??
11:33 PM TurBoss: pwmgen.0.pwm
11:33 PM Lcvette: ok
11:33 PM Lcvette: i get the same patterns as before
11:34 PM TurBoss: ok now in halshow check for pins ->
11:34 PM TurBoss: pwmgen 0
11:34 PM TurBoss: pwm-freq
11:34 PM TurBoss: should be not 333
11:35 PM Lcvette: 0
11:35 PM TurBoss: ok now at botom there is a field input
11:35 PM TurBoss: type
11:35 PM TurBoss: ```
11:35 PM TurBoss: setp pwmgen.0.pwm-freq 333
11:35 PM TurBoss: and test
11:36 PM * Lcvette uploaded an image: Screenshot_2020-03-07_00-29-16.png (55KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/usAozbpdyCQWkcwcdPBcxtad >
11:36 PM TurBoss: same?
11:37 PM * Lcvette uploaded an image: Screenshot_2020-03-07_00-29-59.png (55KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/IqrbmzbmpkxwoPNRCsxvpBkX >
11:37 PM Lcvette: no, more uniform and changes more noticeably
11:37 PM TurBoss: check source channel
11:37 PM Lcvette: top one is no tool and 26degrees
11:37 PM TurBoss: and set rissing
11:38 PM Lcvette: bottom one is 56degrees
11:39 PM Lcvette: rising falling doesn't seem to make any difference
11:40 PM * TurBoss uploaded an image: Captura de pantalla de 2020-03-07 06-33-24.png (52KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/IdTwIjYeUsVTwdjfaDjpTiTx >
11:41 PM Lcvette: what else?
11:41 PM Lcvette: how are yours nice and square and mine are trapezoids?
11:42 PM TurBoss: zoom out
11:42 PM Lcvette: im at 5msec too
11:42 PM TurBoss: pos goes to right
11:43 PM Lcvette: still different
11:43 PM Lcvette: but it is changing with tool changes
11:44 PM TurBoss: we need to figure this
11:44 PM Lcvette: seems we are close
11:44 PM TurBoss: pwmgen.N.max−dc
11:44 PM TurBoss: pwmgen.N.min−d
11:44 PM TurBoss: * pwmgen.N.min−dc
11:44 PM Lcvette: we need to add it?
11:44 PM TurBoss: 1ms 2 ms
11:45 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/nTmgMfnmVNoZSPforpKLnKfu >
11:45 PM TurBoss: or its allready aplied
11:45 PM Lcvette: ok
11:45 PM Lcvette: how to add it properl;y?
11:45 PM TurBoss: with the scale
11:45 PM TurBoss: oh
11:46 PM CaptHindsight: TurBoss: what are your thoughts on using Python for an application that will be used for several years >10?
11:47 PM TurBoss: well if you create a virtualenv and run pip freeze > requirements.txt
11:47 PM TurBoss: that will frooze dependency versions
11:47 PM TurBoss: so no update boom
11:48 PM CaptHindsight: in 10 years with python 7 (or 15) will you be able to run the app without searching for an old version of Python to run it
11:48 PM TurBoss: no
11:48 PM TurBoss: :D
11:49 PM TurBoss: so run with c++ and static linking
11:51 PM CaptHindsight: c++ will probably still be around but will Python be around or an old fad by then?
11:51 PM TurBoss: duno
11:53 PM CaptHindsight: just wondering, thanks
11:53 PM TurBoss: what makes static linked binaries strong is that they have most of their dependencies bundled
11:54 PM CaptHindsight: this would be math intensive
11:54 PM CaptHindsight: 5-axis CAM
11:54 PM TurBoss: nice
11:55 PM TurBoss: Lcvette: I can't figure why ``` setp pwmgen.0.pwm-freq 333 ``` gets ignored or reseted
11:56 PM Lcvette: ok i will look
11:56 PM TurBoss: cool
11:59 PM Lcvette: does make-pulses need a frequency assigned?
11:59 PM * TurBoss uploaded a video: pwmgen.mp4 (212KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/GLhUpAVCOMWpPGXCqWptnIap >