#hazzy Logs

Feb 04 2020

04:56 AM jthornton: morning
07:17 AM hazzy-m: morning
07:22 AM Lcvette: morning
07:23 AM Lcvette: hazzy: hazzy did you see my question? about linuxcnc handling smoothing with g64 P# or fusion handling it?
07:23 AM Lcvette: or both
09:17 AM hazzy-m: Lcvette: yes, he got it working
09:17 AM hazzy-m: I have the post somewhere
09:20 AM Lcvette: did you guys detemrine which was the best?
01:19 PM TurBoss: Lcvette:hello
01:19 PM Lcvette: o/
01:20 PM TurBoss: figured the atc widget?
01:45 PM TurBoss: the tab is a old bug..
03:05 PM Lcvette: yes i fixed it yesterday
03:06 PM Lcvette: was my toolchange.ngc file was missing the debug messages
03:06 PM Lcvette: all is working now
03:06 PM Lcvette: \o/
03:06 PM Lcvette: im about to go cut the parts and take some video
03:06 PM Lcvette: nervous, using some experimental feeds and speeds
03:06 PM Lcvette: :o
03:07 PM Lcvette: cutting at 140ipm at 1" depth of cut and 0.05" stepover
04:24 PM Lcvette: https://youtu.be/LDMKMx2aO5E
04:24 PM Lcvette: :o
05:29 PM TurBoss: \o/
06:00 PM Lcvette: \o/
06:00 PM Lcvette: halo turboss!
06:00 PM Lcvette: * hallo turboss!
06:00 PM Lcvette: did you see the video?
06:00 PM Lcvette: :o
07:03 PM TurBoss: yes
07:03 PM TurBoss: I saw!
07:03 PM TurBoss: you have to put a gopro inbside
07:03 PM TurBoss: * you have to put a gopro inside
07:03 PM TurBoss: * you have to put a gopro inside
07:30 PM TurBoss: hurray debs for buster
07:30 PM TurBoss: !!!
07:30 PM TurBoss: http://buildbot.linuxcnc.org/dists/buster/
08:57 PM Lcvette: lcvette needs to make a gopro case with a spinning disk to keep coolant off of it
08:58 PM TurBoss: \o/
08:58 PM TurBoss: like F1
10:32 PM Lcvette: TurBoss: lol
10:33 PM Lcvette: yo i am getting a bug i think
10:33 PM hazzy-m: Yo
10:33 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/DrydyKxeiqFylawsZePSIWnt >
10:33 PM Lcvette: says i don't have a tool in the casrouselbut i have them all loaded
10:33 PM Lcvette: won't load the program
10:34 PM Lcvette: or the one it loaded fine earlier today
10:34 PM TurBoss: :o
10:34 PM * hazzy-m 's just got back from the bar with three German's, and some poles and swiss lol
10:34 PM Lcvette: i tried restarting but no luck
10:34 PM Lcvette: not sure what to do
10:34 PM TurBoss: sounds like a joke
10:34 PM TurBoss: hmmm
10:35 PM hazzy-m: TurBoss: right lol
10:35 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/pSdprtzweBtnBheRksVUWFgs >
10:35 PM TurBoss: Lcvette: checking...
10:35 PM TurBoss: any ideas?
10:35 PM Lcvette: no clue
10:37 PM Lcvette: https://paste.ubuntu.com/p/r4k9qcJ7nC/
10:37 PM Lcvette: thats the code
10:37 PM Lcvette: but like i said im getting the same error message when trying to load the code it ran fine earlier today
10:37 PM TurBoss: :/
10:38 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/fPhswXYtwVZRKcqDESfOaamD >
10:38 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/rrMkLRDSavBKyGfZIFMygnNw >
10:38 PM Lcvette: var file shows the tool
10:38 PM Lcvette: i dunno why that is there
10:39 PM Lcvette: but its in the same one from easrloier today
10:39 PM Lcvette: i saw that too
10:39 PM TurBoss: :\
10:46 PM TurBoss: :/
10:47 PM Lcvette: i just tried remopving those extra tool numbers after a tool chnage
10:48 PM Lcvette: same thing
10:48 PM Lcvette: don't think its a code problem
10:48 PM Lcvette: since it loaded the file earlier today
10:48 PM TurBoss: give me a sek
10:48 PM TurBoss: I'll boot dev
10:48 PM Lcvette: k
10:49 PM TurBoss: found a way to load the other hdd from mymain destop
10:49 PM TurBoss: using virtualization lol
10:49 PM TurBoss: just boots the real HDD
10:49 PM TurBoss: SDD in the case
10:49 PM Lcvette: sweet
10:50 PM TurBoss: master master?
10:50 PM Lcvette: yes its the latest release installer
10:51 PM Lcvette: v0.1.7
10:53 PM TurBoss: ok
10:54 PM Lcvette: Says vtk backplot
10:54 PM Lcvette: Maybe a bug?
10:55 PM TurBoss: yes because is the last who knows abot file
10:56 PM Lcvette: I don't understand what you said
10:56 PM Lcvette: Lol
10:57 PM TurBoss: it loads
10:59 PM TurBoss: on dev it loads an runs!
11:00 PM Lcvette: It loaded and ran for me earlier fine
11:00 PM Lcvette: Bit now it doesnt
11:00 PM TurBoss: 😕
11:02 PM TurBoss: Lcvette: can I see the full messages with the error?
11:03 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/VipFNviCTotPDokaVYzsVLBT >
11:03 PM Lcvette: and then i click ignore and it gives this one
11:04 PM * Lcvette sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/ojkAfHNTagKPMufgqhGIFbYQ >
11:04 PM TurBoss: the error mentions the vtk backplot because is the one that eecutes "load"
11:04 PM TurBoss: * the error mentions the vtk backplot because is the one that excutes "load"
11:04 PM TurBoss: * the error mentions the vtk backplot because is the one that executes "load"
11:05 PM Lcvette: it loads a different file
11:05 PM Lcvette: that i just ran a few minutes ago
11:05 PM TurBoss: wron file?
11:05 PM TurBoss: * wrong file?
11:05 PM Lcvette: but not thie one i posted on paste
11:05 PM Lcvette: or the one i ran earlier today without issue
11:06 PM TurBoss: the paste load fine here
11:06 PM Lcvette: no
11:06 PM TurBoss: can you upload again?
11:06 PM Lcvette: i even tried downloading the one i posted on matrix and same error
11:06 PM TurBoss: ok
11:06 PM TurBoss: 😕
11:07 PM * Lcvette posted a file: case_machining_op_2.ngc (123KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/ofwLpKLQekLCootdkLKPkBSK >
11:07 PM Lcvette: this is the most current file that won't load
11:09 PM TurBoss: I'm trying with the atc saim
11:09 PM TurBoss: * I'm trying with the atc sim
11:09 PM Lcvette: ok
11:17 PM TurBoss: it fails on atc sim
11:17 PM TurBoss: I didn't had the tools stored
11:17 PM TurBoss: I added the tried but continues failing
11:18 PM Lcvette: so you found the bug too?
11:18 PM Lcvette: imm not going crazy?
11:18 PM Lcvette: so it is something with the loading of the program?
11:19 PM TurBoss: is a error that is fired by the rs274 interpreter
11:19 PM TurBoss: who prints tool not in carousel
11:19 PM TurBoss: must be a sub?
11:20 PM TurBoss: ```
11:20 PM TurBoss: tool not in carousel load tool into carousel using M23 - Manual or M25 - Auto
11:20 PM Lcvette: that looks familiar, let me see if i can find it in a sub somewhere
11:21 PM TurBoss: toolchange line 52
11:22 PM Lcvette: so somehow the next pocket is 0?
11:22 PM Lcvette: so it is triggering that message?
11:27 PM Lcvette: any ideas?
11:27 PM TurBoss: hurray!
11:28 PM Lcvette: you found it?
11:28 PM Lcvette: \o/
11:28 PM TurBoss: \o/
11:28 PM Lcvette: what is it?
11:28 PM TurBoss: at least it loads
11:28 PM TurBoss: check
11:28 PM Lcvette: check?
11:29 PM * TurBoss sent a long message: < https://matrix.org/_matrix/media/r0/download/matrix.org/GQIOzqXzgyRXzkxKiucZrDKX >
11:30 PM TurBoss: open_pocket VS next_pocket
11:30 PM TurBoss: just check that part
11:31 PM TurBoss: wronf
11:31 PM TurBoss: * wrong
11:31 PM TurBoss: diferent logic
11:31 PM Lcvette: ?
11:31 PM Lcvette: full sentences
11:31 PM TurBoss: xD
11:31 PM Lcvette: im trying to follow but falling behind
11:31 PM Lcvette: lol
11:32 PM TurBoss: the first if checks for the tool in all the pockets then stores 12 in next_pocket?
11:32 PM TurBoss: * the first if checks for the tool is in all the pockets then stores 12 in next_pocket?
11:33 PM TurBoss: don't try that yet
11:34 PM TurBoss: just on sim
11:34 PM Lcvette: ok trying on sim
11:34 PM TurBoss: but makes sense?
11:35 PM TurBoss: ah ok 15 is a counter
11:35 PM TurBoss: reversed
11:35 PM TurBoss: * ah ok #15 is a counter
11:35 PM Lcvette: yes
11:35 PM Lcvette: #15 = 12
11:35 PM Lcvette: fort he number of pockets int he carousel
11:35 PM TurBoss: ok
11:36 PM Lcvette: #5189 is pocket 1 in the var file
11:36 PM Lcvette: 5189-5201
11:36 PM Lcvette: carouself pockets
11:36 PM TurBoss: ok
11:36 PM TurBoss: so you check from last to first
11:37 PM TurBoss: ok now i hit the error on run
11:37 PM TurBoss: lol
11:38 PM Lcvette: wait no 5189 is not a pocket i guess
11:38 PM Lcvette: 5190-5201 are pckets
11:38 PM Lcvette: in var file
11:38 PM Lcvette: what is 5189?
11:38 PM TurBoss: 5190 -1
11:39 PM Lcvette: 5181-5189 - "G30" Home for X, Y, Z, A, B, C, U, V & W. Persistent.
11:39 PM TurBoss: homing
11:40 PM Lcvette: but parameter 5189 is being used in the atc remaps
11:40 PM Lcvette: hmmmm
11:43 PM Lcvette: [#[5189+#15] EQ #100]
11:43 PM Lcvette: is this formatted correctly?
11:44 PM Lcvette: maybe 5189 is just a number being used in a calculation and not pulling a variable from the var file?
11:44 PM TurBoss: not 100% sure
11:44 PM Lcvette: im not either
11:46 PM TurBoss: I'm trying to load tool 2
11:46 PM TurBoss: * I'm trying to load tool 2 into carousel
11:46 PM TurBoss: it says tool not on carousel
11:50 PM Lcvette: wqhen you try to load it?
11:50 PM TurBoss: yes
11:50 PM TurBoss: i removed some tools an let me again