#hazzy Logs
Nov 25 2019
#hazzy Calendar
09:39 AM TurBoss: morning
11:40 AM * TurBoss uploaded an image: image.png (323KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/nLHirZGrcvTBXhZrLDDfTgle >
11:40 AM TurBoss: Lcvette Lcvette !!!!
11:41 AM TurBoss: \o/
11:42 AM Lcvette: :o
11:42 AM Lcvette: you did it?
11:42 AM Lcvette: \o/
11:42 AM TurBoss: part of
11:43 AM TurBoss: only one rapid left
11:43 AM Lcvette: \o/
11:43 AM Lcvette: i see the rapidd lines are gone!
11:43 AM Lcvette: hurray!
11:45 AM Not-5e4d: [02qtpyvcp] 07TurBoss pushed 031 commit to 03VtkGx [+0/-0/Âą1] 13https://git.io/JePzf
11:45 AM Not-5e4d: [02qtpyvcp] 07TurBoss 033cd3810 - remove extra rapids after change offset
11:45 AM Lcvette: is it in kraken?
11:45 AM Lcvette: \o/
11:45 AM TurBoss: yes!!
11:45 AM Lcvette: lcvette will test while eating lunch!~
11:45 AM TurBoss: :D
11:45 AM Lcvette: ok testing
11:45 AM TurBoss: coool thank you
12:11 PM Lcvette: TurBoss: \o/
12:11 PM Lcvette: tested looks right!!
12:13 PM TurBoss: amazing!
12:15 PM TurBoss: we are close to merge
12:16 PM Lcvette: hurray!!
12:16 PM Lcvette: \o/
12:16 PM Lcvette: i got mjy probe receiver back setup for 24v today!
12:16 PM Lcvette: \o/
12:16 PM Lcvette: perfect timing!
12:16 PM Lcvette: i will install this evening maybe
12:16 PM Lcvette: need to test it out
12:18 PM TurBoss: nice
12:19 PM TurBoss: so you have the first 24v probe?
12:20 PM Lcvette: the receiver was changed from 5v to 24v
12:20 PM Lcvette: probe is same probe still
12:27 PM Lcvette: TurBoss: the program boundary is not updating still
12:27 PM TurBoss: crashed
12:27 PM TurBoss: ok
12:28 PM * Lcvette uploaded an image: Screenshot_2019-11-25_13-21-33.png (37KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/lotdwPflBHbnkWLdRrNcneUa >
12:28 PM TurBoss: yup
12:28 PM Lcvette: crashed
12:28 PM Lcvette: :o
12:28 PM TurBoss: nono
12:28 PM TurBoss: joke
12:29 PM Lcvette: it updates if i close the program and reopen
12:30 PM TurBoss: brb
12:30 PM Lcvette: ok
12:41 PM * Lcvette uploaded an image: Screenshot_2019-11-25_13-35-03.png (72KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/QkEzRdRcNikBXkRsvwNdwlOc >
12:41 PM Lcvette: looks right!
12:42 PM * Lcvette uploaded an image: Screenshot_2019-11-25_13-35-51.png (13KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/KKtRgSUGPeLubwcYoiulcGVi >
12:42 PM Lcvette: doh
12:42 PM Lcvette: looks like there is one straggler left
12:43 PM * Lcvette uploaded an image: Screenshot_2019-11-25_13-36-27.png (43KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/PULIMqWfMXvghcGKoVcZSkPy >
01:22 PM Wandoo1980|Sebas: Hi there đ I am back ^^
01:25 PM Wandoo1980|Sebas: because of crash
01:25 PM Wandoo1980|Sebas: https://youtu.be/JFlf-vmX8R8
01:25 PM Wandoo1980|Sebas: đ
02:10 PM TurBoss: wow
02:10 PM TurBoss: did you find why?
02:12 PM TurBoss: hey Lcvette i saw that line
02:12 PM TurBoss: i have to figure it yet
02:24 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: Wandoo1980 | Sebastian | End-CNC :o
02:24 PM Lcvette: whats happened?
02:24 PM Lcvette: TurBoss: i did not find out why the lines are there
02:25 PM Lcvette: what fixed the other lines?
02:25 PM Wandoo1980|Sebas: I measured the z 0 wrong
02:25 PM TurBoss: sikp 2 points
02:25 PM Wandoo1980|Sebas: đ
02:25 PM Lcvette: i can look and throw out wild ideas and speculation!! :D
02:25 PM Lcvette: Wandoo!!!! lol
02:25 PM Lcvette: that crash looked violent
02:25 PM TurBoss: /o\
02:26 PM Lcvette: /o\
02:26 PM Lcvette: was it wandoo bug or probe basic bug?
02:26 PM Wandoo1980|Sebas: I was also very excited đ
02:27 PM Wandoo1980|Sebas: Unfortunately I do not know it
02:27 PM Wandoo1980|Sebas: I had the problem that I was suddenly in g20
02:27 PM Wandoo1980|Sebas: but so far I could not reproduce that
02:28 PM TurBoss: âšī¸
02:28 PM Wandoo1980|Sebas: and at the crash, I had not paid attention
02:28 PM Wandoo1980|Sebas: but the machine is fine
02:28 PM Lcvette: https://www.youtube.com/watch?v=f92oimED8PQ
02:29 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: ^^
02:29 PM TurBoss: xDD
02:29 PM Lcvette: that was a time i bumped the coolant nozzle out of the tool path and it ran dry and chip welded
02:29 PM Lcvette: lol
02:29 PM Lcvette: the tts holder pulled out of the collet
02:30 PM Wandoo1980|Sebas: ups ^^
02:30 PM Lcvette: was ugly
02:30 PM Lcvette: big oops
02:30 PM Lcvette: lol
02:31 PM Lcvette: not sure about the G20 still
02:31 PM Lcvette: do you have G21 in your startup line?
02:32 PM Lcvette: when the mill powers on
02:32 PM Lcvette: in the ini file?
02:32 PM Wandoo1980|Sebas: I try to watch it
02:32 PM Wandoo1980|Sebas: if I exchange my tools with M6G43T99, everything is ok
02:32 PM Wandoo1980|Sebas: Yes
02:33 PM Lcvette: RS274NGC_STARTUP_CODE = F10 S300 G20 G17 G40 G49 G54 G64 P0.001 G80 G90 G91.1 G92.1 G94 G97 G98
02:33 PM Lcvette: ok
02:34 PM Wandoo1980|Sebas: I think I'll provoke it in the next few days
02:34 PM Wandoo1980|Sebas: but without tools ^^
02:34 PM Wandoo1980|Sebas: đ
02:36 PM Lcvette: smart thinking
02:39 PM Wandoo1980|Sebas: The screen works very well
02:39 PM Wandoo1980|Sebas: I did not have to switch to axis until now đ
02:39 PM Wandoo1980|Sebas: and I do not want it anymore đ
02:39 PM Lcvette: thats good to hear!!
02:41 PM Lcvette: run me through what happened when the g20 thing happened
02:41 PM Lcvette: i will go through the gui and make sure there are not any forgotten g20 codes anywhere that are causing the issue
02:42 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: Wandoo1980 | Sebastian | End-CNC ^^
02:43 PM Wandoo1980|Sebas: I have changed the tools in the tool change side and not with the mdi
02:43 PM Wandoo1980|Sebas: that's the only thing I did differently than usual
02:43 PM Wandoo1980|Sebas: normally I change the tools with M6
02:44 PM Wandoo1980|Sebas: You said you used on the page M61 Q--
02:44 PM Lcvette: yes
02:44 PM Wandoo1980|Sebas: do I remember that right?
02:44 PM Lcvette: that should not change g20
02:44 PM Lcvette: i was just checking again
02:45 PM Lcvette: it is just M61 Q(number pulled from the corresponding tool number box entry)
02:47 PM * Lcvette uploaded an image: Screenshot_2019-11-25_15-40-43.png (162KB) < https://matrix.org/_matrix/media/r0/download/matrix.org/RYwggcswqhFrQfHNkQNscBFZ >
02:47 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: ^^^
02:48 PM Lcvette: LOAD SPINDLE button = M61 Q#<load_spindle_tool_number>
02:48 PM Wandoo1980|Sebas: Yes
02:48 PM Wandoo1980|Sebas: hmmm, crazy đ
02:48 PM Lcvette: so should be same as typing M61 Q(tool number) in mdi
02:49 PM Lcvette: the M6 button = T#<atc_tool_number_entry_box> M6
02:50 PM Lcvette: so would be T0M6 in the above pictured screen
02:50 PM Wandoo1980|Sebas: Yes, i will try that. As you say, that cannot be the fault
02:50 PM Lcvette: again should not cause a switch to G20
02:50 PM Wandoo1980|Sebas: <span class="d-emoji">:verwirrt:</span>
02:51 PM Lcvette: very strange
02:51 PM Lcvette: were you probing?
02:53 PM Wandoo1980|Sebas: I'm currently not on the machine. I have to got to bed in a view minutes ^^
02:53 PM Lcvette: ok
02:54 PM Lcvette: no code issue from the program was it?
02:54 PM Wandoo1980|Sebas: no, the program works fine. I have run it after the crash again without any fault
02:55 PM Lcvette: M61 Q0 G49 #5210 = 0
02:55 PM Lcvette: this is the unload spindle command
02:55 PM Lcvette: maybe it turned off the offset and you did not turn it back on?
02:56 PM Wandoo1980|Sebas: okay, it can not be so, it is simply just set the variable to 0
02:56 PM Wandoo1980|Sebas: i have a G43 in the first lines of my code
02:57 PM Lcvette: ok
02:57 PM * Wandoo1980|Sebas posted a file: Schlichten_2.ngc (9930KB) < https://matrix.org/_matrix/media/r0/download/jauriarts.org/gXmXltCflxMIEaPOSTgoFgBo >
02:57 PM Wandoo1980|Sebas: That's an example ^^
02:58 PM Wandoo1980|Sebas: đ
02:59 PM Wandoo1980|Sebas: it's only a test to stress all three axis for a long time simultaneous
03:03 PM Lcvette: im loading it now
03:03 PM Lcvette: had to add tool 71
03:04 PM Lcvette: thats a big file!
03:04 PM Lcvette: takes a few seconds too load
03:04 PM Wandoo1980|Sebas: A little bit ^^
03:04 PM Wandoo1980|Sebas: 3d code ^^
03:08 PM Lcvette: im running a test on it now
03:08 PM Lcvette: seems to be doing fine!
03:08 PM Lcvette: my setup is in G20 for start up
03:09 PM Lcvette: but it switches fine to G21 at program start
03:09 PM Lcvette: im getting the correct tool offset
03:25 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: i tried to reproduce the g20 issue but cannot
03:25 PM Lcvette: i ran your code through and it was good
03:28 PM Lcvette: turboss i found another bug with vtk
03:28 PM Lcvette: the part origin remains after closing a program as well
03:37 PM Wandoo1980|Sebas: That's good news. I have to go to bed now ^^ See you tomorrow
03:37 PM Lcvette: Wandoo1980 | Sebastian | End-CNC: night
03:38 PM Lcvette: turboss, disregard, its notmal
03:38 PM Lcvette: lol
07:09 PM Tom_itx is now known as Tom_L