#garfield Logs

Mar 15 2024

12:22 PM rue_mohr: -
01:35 PM aandrew_ is now known as aandrew
01:44 PM rue_mohr: ok its almost 12:00
01:45 PM rue_mohr: I need to figure out what I am supposed to do today
02:03 PM rue_mohr: awe, the computer I set up for myself last night was a 32 bit install, not 64, and the 16G of ram from china looks bogus (woo surprise!)
02:04 PM rue_mohr: but its odd, the memory tester crashes
02:04 PM rue_mohr: ugh, I have to get up and go do things
06:38 PM rue_shop2: hi rif
08:08 PM rue_shop2: damni t, the ream overcut the hole
08:11 PM Tom_L: how much?
08:45 PM rue_mohr: loose fit
08:46 PM rue_mohr: glueable
09:54 PM rue_mohr: https://ton.twitter.com/i/ton/data/dm/1767850358242525517/1767850352110346240/jDwrjpVj.jpg:large
09:54 PM rue_mohr: oh the pulley took the 10krpm, no explosions
09:55 PM rue_mohr: seems to be balanced pretty good
09:55 PM rue_mohr: tomorrow maybe I can focus on mounting it all
10:47 PM Tom_itx: twitter didn't load
10:48 PM Tom_itx is now known as Tom_L
10:59 PM rue_mohr: oh, its just a schematic for me
11:00 PM rue_mohr: a ROM FSM based clock
11:00 PM rue_mohr: each bit of the ROM is a serial stream
11:00 PM rue_mohr: two of the streams determine the next address, and 4 others determine the BCD digits to display
11:37 PM VanUnamed: rue_mohr:
11:37 PM VanUnamed: printer keeps being out of level.
11:37 PM rue_mohr: mhm
11:37 PM rue_mohr: something is slowly coming apart
11:38 PM VanUnamed: i do the four corner thing
11:38 PM VanUnamed: but when it goes to print
11:38 PM rue_mohr: mhm
11:38 PM VanUnamed: it's like one side is highm and one is low
11:38 PM rue_mohr: something is falling apart
11:38 PM VanUnamed: and thats even when the blt touch maps the bed.
11:38 PM rue_mohr: likley a nut somewhere
11:38 PM rue_mohr: its slowly sliding apart
11:39 PM rue_mohr: as the print runs,
11:39 PM VanUnamed: it's the first layer.
11:39 PM rue_mohr: it will fail completely during a print and make you a pile of spagetti
11:40 PM VanUnamed: it does squeal a little on the z
11:40 PM VanUnamed: should i put some ten wforty?
11:44 PM rue_mohr: 5w30 maybe
11:44 PM VanUnamed: can it be my bed is seriously crooked?
11:44 PM VanUnamed: yet, software should correct, but it does not
11:45 PM rue_mohr: it does, the error happens after
11:45 PM VanUnamed: how?
11:46 PM rue_mohr: I think something is slowly coming apart
11:46 PM VanUnamed: what could it be
11:46 PM rue_mohr: well if you made your printer from scratch you would know
11:54 PM rifraf: evening all
11:54 PM VanUnamed: any hint?
11:54 PM rue_mohr: VanUnamed, I didn't build your machine :/
11:54 PM rue_mohr: rifraf, hi
11:54 PM VanUnamed: i dint build it either
11:54 PM rue_mohr: if you had, it would be fixed by now
11:55 PM rue_mohr: aliexpress.com/item/4000578960965.html
11:55 PM rue_mohr: ^^ rifraf suggest me a heavy drive belt for a 2m cnc machine
11:55 PM rue_mohr: but not that one, its too expensive
11:55 PM rue_mohr: chain?
11:55 PM rue_mohr: are you sure?
11:56 PM VanUnamed: ok then, have you got any pointer to waht it could be that is coming lose and causing this
11:57 PM VanUnamed: which area should i look at more
11:57 PM rue_mohr: I think the two times that happened to me, the Z rod was falling off the stepper motor
11:58 PM VanUnamed: that is where the squealing comes from
11:58 PM rue_mohr: are your motors on the top or bottom?
11:59 PM rue_mohr: Z
11:59 PM VanUnamed: bottom
11:59 PM VanUnamed: motor, singular
11:59 PM VanUnamed: it's a ender three
11:59 PM rue_mohr: I didn't build it :]