#garfield Logs

Mar 20 2023

12:24 AM rue_mohr: want me to take some measure ments for ya?
04:28 AM Tom_L: did it fit ok?
04:28 AM Tom_L: only if you think you may need another anytime
04:28 AM Tom_L: measure before it's worn out
07:21 AM rue_mohr: I still need to finish building a head
02:04 PM Tom_L: i'm gonna draw up the fixture for reference. i may need a few dimensions.
02:04 PM Tom_L: i did find the top half of one i redid
07:18 PM Tom_L: when you get a chance i'd like to go over these dimensions
07:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions1.jpg
07:18 PM rue_mohr: ok
07:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions2.jpg
07:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions3.jpg
07:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions4.jpg
07:19 PM Tom_L: i drew them that way you can tell me what dimension is wrong
07:20 PM rue_mohr: ok
07:20 PM Tom_L: i either have some memory going out or the mb
07:33 PM Tom_L: works fine when i boot 32bit but when i boot 64bit it crashes
07:33 PM Tom_L: i tried the ssd in another mb and it worked fine
07:33 PM Tom_L: may just swap mb & memory rather than testing the memory
08:05 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/assembly1.jpg
08:05 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/assembly2.jpg
09:04 PM rue_shop4: 1.jpg....
09:05 PM rue_shop4: the inner channel is actually 0.862
09:06 PM Tom_L: lemme pull it up
09:06 PM rue_shop4: everything else is ok
09:06 PM rue_shop4: 2.jpg is fine
09:07 PM Tom_L: the .928 should be .862?
09:07 PM rue_shop4: yes
09:07 PM Tom_L: ok got that
09:07 PM Tom_L: i guessed on the bottom bar completely
09:08 PM rue_shop4: 3.jpg
09:08 PM rue_shop4: the .596 should be .592?
09:08 PM Tom_L: ok that will give it a little clearance and it's not critical
09:09 PM rue_shop4: 4.jpg
09:09 PM Tom_L: the distance inside the slot minus 2 dowels
09:09 PM rue_shop4: 2 should be 1.453
09:10 PM rue_shop4: 0.750 should be 0.642
09:10 PM rue_shop4: other than that it all matches
09:10 PM Tom_L: 2 should be 1.453?
09:10 PM Tom_L: where's that
09:11 PM Tom_L: on #4?
09:11 PM rue_shop4: 4.jpg
09:11 PM Tom_L: oh that doesn't matter.. it's just a spacer for the dowels
09:11 PM Tom_L: but ok
09:12 PM rue_shop4: yup
09:13 PM Tom_L: .750 is on the spacer block width?
09:13 PM Tom_L: yeah both those are ok
09:13 PM Tom_L: one critical one i missed was the width of the base rectangle
09:13 PM Tom_L: what the A9 sits on
09:13 PM Tom_L: for the inside bend
09:14 PM Tom_L: i have .669" wide for that
09:14 PM Tom_L: the jpg doesn't show it
09:14 PM Tom_L: should have been on 3.jpg
09:25 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions5.jpg
09:25 PM Tom_L: i need to verify the .669" it's critical
09:46 PM rue_mohr: sorry, I can check again for ya after supper here
09:50 PM Tom_L: ok but i'm not stayin up much longer
09:58 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions6.jpg
10:00 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions7.jpg
10:00 PM Tom_L: in case you want a copy
10:02 PM rue_shop4: ok
10:03 PM rue_shop4: 0.592
10:03 PM rue_shop4: 5.jpg
10:04 PM rue_shop4: if I were trying to make one, I'm not sure how I'd do it
10:05 PM Tom_L: the width is .592??
10:05 PM Tom_L: mmm kay
10:08 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/rue/Can_Holder/A9_Bender/Dimensions6.jpg
10:08 PM Tom_L: updated
10:09 PM rue_shop4: so, how did you lose the design?
10:09 PM Tom_L: i scribbled it on a piece of toilet paper :)
10:09 PM Tom_L: naw... but close
10:09 PM rue_shop4: heh
10:09 PM Tom_L: it was one of those 'in the head' designs
10:11 PM Tom_L: and on the holes, i have 2 reamers.. one is oversize
10:11 PM Tom_L: ok i think that should be all of it now. i'll check it over close tomorrow
10:12 PM Tom_L: thanks
10:36 PM rue_shop4: oh do you want me to double check the holes?