#garfield Logs

Mar 26 2019

09:59 PM mooonmoonmoon: rue_mohr: :P
10:03 PM mooonmoonmoon: rue_bed: PIONK
10:09 PM zhanx: rue car is back
10:10 PM zhanx: i got your address, sending mail
10:10 PM zhanx: and lots for moon
10:10 PM zhanx: mooonmoonmoon, your getting a bunch of the electronics
10:12 PM mooonmoonmoon: ooh thank you zhanx
10:13 PM zhanx: thank my wife
10:13 PM Tom_L: she makin you clean house?
10:13 PM zhanx: yep
10:13 PM mooonmoonmoon: I wont be back near rue_mohr for another 8 weeks, but I lookforward to mail
10:14 PM zhanx: Tom_L, it was 900 for the suv
10:14 PM zhanx: new front end and tires, brakes all the way around
10:34 PM rue_mohr: hi
10:34 PM rue_mohr: ah cool, thanks
10:34 PM Tom_L: zhanx i bet you were excited too
10:34 PM rue_mohr: they didn't charge ya for the blunders, right?
10:35 PM zhanx: rue no they didn't
10:37 PM Tom_L: what front end pieced did they replace?
10:37 PM Tom_L: 'front end' covers alot of ground
10:37 PM zhanx: i bought up and lower ball joints, tie rod ends
10:38 PM Tom_L: what about A arm bushings?
10:38 PM Tom_L: they still good?
10:38 PM zhanx: they were fine
10:38 PM zhanx: drives like a new car now
10:38 PM Tom_L: nice
10:38 PM zhanx: wife saw the cost and was pissed
10:39 PM zhanx: so i broke it down to her
10:39 PM zhanx: now she wants to trade vehicles
10:40 PM zhanx: Tom_L, for about 900 only thing left in the drive train to change is the carrier bearing
10:42 PM Tom_L: is it rattling around?
10:42 PM zhanx: nope, its suspect is all
10:42 PM zhanx: 20 bucks and a hammer to fix it
10:42 PM Tom_L: rubber boot could be wore out
10:43 PM zhanx: boot is but the bearing i keep greased
10:51 PM mooonmoonmoon: rue_mohr: what you doing?
10:52 PM zhanx: probably working on his servo control
10:52 PM mooonmoonmoon: hm , with IP stylings no doubt
10:53 PM zhanx: programmed via isa
10:53 PM mooonmoonmoon: I was telling him he sould make "adult toys" with his force feed back ;P
10:53 PM mooonmoonmoon: isa?
10:53 PM zhanx: isa card slots
10:53 PM zhanx: for pc
10:54 PM mooonmoonmoon: oh I did not know he was doing that
10:54 PM rue_mohr: pff
10:54 PM mooonmoonmoon: pff yourself
10:54 PM rue_mohr: I'm installing a serial port for debug :/
10:54 PM rue_mohr: the proposition is that, the code works
10:54 PM mooonmoonmoon: is this anything to do with a Zilog?
10:55 PM rue_mohr: not yet
10:55 PM rue_mohr: building that 4' x 8' cnc
10:55 PM mooonmoonmoon: starting already hay
10:55 PM zhanx: i am wondering if this 1/2" flow meter can handle 220F
10:56 PM rue_mohr: whats that in C?
10:56 PM zhanx: 100c
10:56 PM rue_mohr: look at the plastic, the high temp stuff has that slightly brittle thing going on
10:57 PM zhanx: its 0 for can't land on the moon and 220% landed on the moon units
10:57 PM zhanx: its brittle
10:57 PM rue_mohr: prolly ok then
10:58 PM zhanx: gonna just boil water in a pot and pump water to test it i think
10:59 PM rue_mohr: I got some for my boiler, but that tops out at 80c
10:59 PM zhanx: k
10:59 PM zhanx: only need the 100c for about 10 minutes
10:59 PM zhanx: its for a whirlpool
11:00 PM mooonmoonmoon: gnight homies