#garfield Logs
Apr 09 2018
#garfield Calendar
12:00 AM ^kat^: that was my desire too
12:03 AM ^kat^: same hardware could be used to map pins on relays or other oddball parts
12:03 AM rue_mohr: I can do soic with a sharp pen
12:03 AM ^kat^: hit record, manually move the bit to the pins
12:03 AM rue_mohr: map pins...?
12:03 AM rue_mohr: huh, not my plotter
12:03 AM rue_mohr: but ok
12:03 AM ^kat^: k
12:03 AM ^kat^: erg, brb
12:03 AM rue_mohr: burning smell from the kitchen?
12:09 AM ^kat^: no, had to add ingrediments, 8 min more to cook
12:09 AM rue_mohr: fancy
12:09 AM rue_mohr: well, its past bedtime for a worknight for me
12:09 AM ^kat^: k, happy sleeps
12:09 AM rue_mohr: if I do
12:09 AM rue_mohr: (arg)
12:09 AM ^kat^: ditto
12:09 AM rue_mohr: maybe I should take 3 melatonin now
12:09 AM * ^kat^ quotes a ditto: """
12:09 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/semiparts2.jpg
12:09 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/semiparts3.jpg
12:09 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/semiparts5.jpg
12:09 AM rue_mohr: updated images will not stress neck
12:09 AM ^kat^: same pics,, why?
12:09 AM ^kat^: you do not log the qty , why?
12:09 AM rue_mohr: dont care
12:09 AM rue_mohr: usually only use a few at a time
12:09 AM rue_mohr: just want to know if I have ANY
12:11 AM rue_mohr: lots of eproms
12:11 AM ^kat^: i tried to avoid 74HC and 74LS , but got a few anyhow, and LVC,LVX
12:12 AM ^kat^: went for ABT if i could, or F
12:12 AM rue_mohr: this melatonin thing backfired on my last week, went to sleep ok, and woke up 3 hours early in the morning
12:13 AM rue_mohr: short the same amount of sleep
12:13 AM ^kat^: swallow 2, suck on one?
12:13 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/p1030166.jpg it looked so clean...
12:14 AM ^kat^: cute windows and carriage lites
12:14 AM rue_mohr: :)
12:16 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/dscn9930.jpg
12:16 AM rue_mohr: it was so spacious
12:16 AM rue_mohr: http://ruemohr.org/~ircjunk/shop/dscn9926.jpg
12:17 AM rue_mohr: got high as a kite doing that floor
12:17 AM rue_mohr: almost all worn off now
12:17 AM ^kat^: and all that subfloor piping
12:18 AM rue_mohr: the runs to the middle table are 1/2 pvc, I put plumbing 90's in them
12:18 AM rue_mohr: man was that wire hard to pull in
12:19 AM ^kat^: heh
12:20 AM ^kat^: when i poured the fluted columns outside, i put 1/2 cpvc in them to run downlites uder a cast cap block
12:20 AM ^kat^: wiring was all overhead, cept the 240, which was under the slab to the downstairs utility room
12:21 AM * ^kat^ gets dinner
12:25 AM rue_bed: I got more steel today
12:25 AM ^kat^: back
12:25 AM rue_bed: some 1/2" plate that might make good stuff for a cnc machine
12:27 AM ^kat^: i looked at my stock today too, found stuff i had forgotten wheni was coverg one of the rain gutters across the driveway
12:27 AM ^kat^: 1" , 3/4" , 1/2" for milland lathe tables
12:33 AM ^kat^: got a 14inch x 4ft slab of 3/4 at scrap yard
12:33 AM ^kat^: got a large pile of 1" (?) roughing end mills too
12:33 AM ^kat^: nothing to put them i yet
12:37 AM ^kat^: rue didn;t say anyting about the boxes of hdds
12:38 AM ^kat^: and there's 16 desktops with 3 or 4 hdd in them, plus the sata hdds piled up
12:41 AM ^kat^: 48v batt chgrs?
12:48 AM ^kat^: i must have been hungry, i just ate toomuch
12:48 AM rue_bed: ditto
12:48 AM * rue_bed rolls over again
01:30 AM ^kat^: gnites
08:48 AM Tom_L: so, i need to change the ip on the server.. does that require a reboot or apache restart?
10:11 PM Tom_L: stretch is a pita
10:11 PM Tom_L: doesn't load enough gnuc to compile
10:41 PM katsmeow: notice those 12vdc 30amp switchers have gotten upto $18 each, and more, lately? i might be able to grab one for $11.50 free s&h
10:41 PM katsmeow: someone actually put one up on auction, not buy-it-now
10:45 PM katsmeow: to win against me now, someone will haveto bid $15, and they are available for $15 as buy-now, if you know where to look
10:49 PM katsmeow: <coff>
11:22 PM katsmeow: won it for $11.50
11:41 PM rue_mohr: hi
11:42 PM rue_mohr: Tom_L, so I need to rough out a cnc design
11:42 PM katsmeow: hi
11:42 PM rue_mohr: katsmeow, I bet some idiot will do it
11:42 PM rue_mohr: I played that game a few times
11:45 PM katsmeow: do what?
11:45 PM rue_mohr: bidding such that someone would have to pay mor thant he buy-it-now price
11:45 PM rue_mohr: and they did, matter a fact, most of the time they went higher than the buy=-it-now
11:46 PM rue_mohr: !?!?!?! WTF?
11:46 PM katsmeow: erg, sleeping pills kicking in early, i just tried to access a puter that wasn;t even turned on
11:46 PM rue_mohr: https://www.aliexpress.com/item/220V-2-2KW-ER20-CNC-Water-Cooling-Spindle-85mm-Metal-Spindle-2-2kw-VFD-Variable-Frequency/32435769107.html
11:46 PM rue_mohr: ali keeps offering that to me, I'm NOT gonna buy it!
11:46 PM katsmeow: no one bid, i got it for $11.50
11:46 PM rue_mohr: nice
11:47 PM katsmeow: yipes @ $555 for a motor and non-replaceable collet chuck
11:47 PM rue_mohr: I suppose I can make a water cooling jacket for a motor from PLA, cause, if it gets hot enough to melt it, something didn't work
11:49 PM katsmeow: now i wonder if it will be delivered to me
11:51 PM rue_mohr: have you ever opened up a 10 turn pot?
11:51 PM rue_mohr: klarge panel mount one
11:53 PM katsmeow: one, but not all built alike
11:54 PM rue_mohr: do they use some combination of rotating and linear sliding?
11:54 PM rue_mohr: they SOUND like a rotation on a wire wound resistor
11:55 PM rue_mohr: https://www.aliexpress.com/item/12-8-cm-motorized-fader-remote-motor-potentiometer-N-frequency-single-joint-B10K-8T/32458879036.html
11:56 PM rue_mohr: no cheap servo options there
11:56 PM katsmeow: some use a spiral element, some use a allthread and linear elemant
11:56 PM katsmeow: some use a regular pot and a friction planetary drive
11:56 PM katsmeow: those usually screw up tho
11:57 PM rue_mohr: https://www.aliexpress.com/item/BELLA-Original-Japan-ALPS-motorized-faders-12-8-cm-Single-Slide-fader-potentiometer-B10K-3/1389297065.html
11:57 PM rue_mohr: I suppose I can just make those
11:57 PM rue_mohr: the slide resistors I have, have two tracks
11:58 PM rue_mohr: one could be used for feedback
11:59 PM rue_mohr: 8-| even those resistors aren't cheap