Back
[00:10:29] <rue_shop3> yea
[00:10:32] <rue_shop3> and everything
[00:11:13] <rue_shop3> economy is in a state where nobody can afford to buy things that are made by people who are paid a living wadge
[00:12:03] <rue_shop3> :) I'v got a rotation sensor on the spindle!
[00:13:58] <zhanx> nice
[00:30:50] <rue_house> at some point I'll post a bunch of puics
[00:30:56] <rue_house> progress is slower than Iwant
[00:31:10] <rue_house> I wanted to get a motor driver and a spindle interrupter on today, just got the spindle
[00:31:39] <rue_house> I found two old fet driver pcb's that aren't assembled
[00:31:43] <rue_house> er three
[01:07:45] <Jymmm> Crap 29F =(
[01:08:49] <Jymmm> Ok fsck me... predicted to go down to 21F tonight
[01:14:04] <zhanx> thats it?
[01:14:27] <zhanx> want to vist the north country for a bit?
[02:31:40] <rue_house> yea, I want to integrate it, cause the amount of constant error at full signal would be huge
[10:01:01] <Jymmm> rue_shop3: I was reading an article on heatpumps. Mentined using a tankless water heater for "aux" heat (instead of the electric strips during defrost cycle),...
[10:02:33] <Jymmm> rue_shop3: Since the defrost cycle is 45-90 seconds, you think there is a way to generate that much heat into the circulation system by tossing a radiator into the duct work?
[10:07:07] <Jymmm> rue_shop3: Actually a good read (and the links it provides) on heat pumps and the like...
http://www.energyvanguard.com/blog/69996/The-Shocking-Truth-About-Heat-Pumps
[19:34:35] <rue_house> Jymmm, tom dosn't make his programmers anymore, just go for an usbasp
[19:34:39] <rue_house> like $3
[19:40:59] <Jymmm> rue_house: JTAG?
[20:04:10] <Tom_L> i have a couple left
[20:04:27] <Jymmm> I was looking for a JTAG
[20:04:43] <Tom_L> get the one from atmel that does everything
[20:04:54] <Tom_L> it's about 50 for a bare board
[20:06:33] <Tom_L> http://www.digikey.com/product-detail/en/microchip-technology/ATATMEL-ICE/ATATMEL-ICE-ND/4753379
[20:06:44] <Tom_L> that's with the case and cables
[20:07:16] <Tom_L> http://www.digikey.com/product-detail/en/microchip-technology/ATATMEL-ICE-PCBA/ATATMEL-ICE-PCBA-ND/4753383
[20:07:19] <Tom_L> bare board
[20:12:11] <Jymmm> Whats the OSX/linux equiv of Atmel Studio?
[20:13:16] <Tom_L> beats the hellouttame
[20:13:35] <Tom_L> why do you need studio?
[20:13:41] <rue_house> dont use jtag
[20:13:42] <Tom_L> use an editor and avr-gcc
[20:13:50] <Tom_L> and debug with an led
[20:13:57] <rue_house> dont use an emulator
[20:14:36] <rue_house> an "led" will give you more accurate debug results, esp if you have a scope
[20:14:51] <rue_house> the led can also be a serial output
[20:15:48] <rue_house> you see, then its all real-world
[20:16:07] <rue_house> no stopping the processor, no simulator glitches
[20:30:58] <Jymmm> rue_house: jtag was for unbricking/hacking... "things"
[23:10:18] <rue_house> to my experience there is no universal jtag
[23:10:23] <rue_house> funny enough