#garfield Logs

Nov 17 2015

00:22 katsmeow http://www.harborfreight.com/3-in-heavy-duty-electric-cut-off-tool-68523.html
00:23 katsmeow can you change the adapter to a collet type of termination?
00:23 katsmeow aka make a new one to hold bits in collets
00:30 katsmeow like those 1/4 inch rotary tools that use as sidcutter bit to cut sheetrock
00:30 katsmeow or 1/8 dremels
00:40 katsmeow Series Range In. (mm) # of collets in set
00:40 katsmeow ER11 0.020-0.275 (0.5-7) 13
00:40 katsmeow ER16 0.020-0.393 (0.5-10) 10
00:40 katsmeow ER20 0.039-0.511 (1-13) 12
00:40 katsmeow ER25 0.039-0.629 (1-16) 15
00:40 katsmeow ER32 0.078-0.787 (2-20) 18
00:40 katsmeow ER40 0.118-1.023 (3-26) 23
00:41 katsmeow so making shaft adapter to relce the em one, in ER11 or ER16 might be handy
00:49 katsmeow www.ebay.com/itm/DIY-Cnc-Milll-Router-lathe-ER11-Straight-Shank-Extend-100mm-spindle-Dia-12MM-/391304578390cut this assort as pussible, to sli[ so tha screw onto the motor saft
00:56 katsmeow http://www.ebay.com/itm/CNC-Straight-Shank-Chuck-C8-ER8A-100L-Deep-Processing-/161320357029
01:03 katsmeow gnites
18:19 ^kat^ <ding> rue, you have email </ding>
19:37 rue_more its hard to tell the difference between a 30w led flood in the eyes from a 50w led flood in the eyes
19:38 rue_more drat, I missed the timeframe
19:40 rue_more I wonder where it is, there are a number of closed pulp mills in BC
19:50 ^kat^-afk http://imgur.com/gallery/Md4wsnv
19:51 rue_more nicely done
19:51 ^kat^-afk i didn't build that one
19:54 rue_more :)
19:54 rue_more it needs my motion control software
19:55 rue_more its got awkward interpolation
19:55 ^kat^-afk http://imgur.com/gallery/owqRfVV
19:55 rue_more caught that one
20:18 ^kat^-afk can i make a split nut for lathe table just by splitting a nut?
20:18 ^kat^-afk or is it more complicated?
20:18 ^kat^-afk can i use chain instead of allthread?
20:25 ^kat^-afk FINALLY, a shaft measurement that makes SENSE! ; http://www.ebay.com/itm/181421830523 ; Shank diameter: 15.94mm
20:27 ^kat^-afk and 7 collets for it for $10.50
20:27 ^kat^-afk spin it up with that $25 25,000 rpm motor
20:28 ^kat^-afk prolly need a lot of soundproofing tho
20:28 ^kat^-afk Accuracy: 0.015mm
20:28 ^kat^-afk Model: ER11 (7pcs,)
20:28 ^kat^-afk (1/16",3/32",1/8",5/32",3/16",7/32",1/4")
20:29 ^kat^-afk .015mm is 0.00059inches
22:10 ^kat^-afk got one of the barrel clamps completed : http://designerthinking.com/JL/DSCF6818m.jpg
22:11 ^kat^-afk of course, i had to take the two center barrels out to get the pic, othersise you'd barely see that , even if you looked for it
22:21 ^kat^-afk http://www.livescience.com/11892-video-caterpillar-beach-room.html
23:27 zhanx Rue you around?
23:28 ^kat^-afk no
23:29 ^kat^-afk not for 4 hrs
23:37 ^kat^-afk so "Cherry 2000" isn't really about porn, it's about robots and peoples
23:37 ^kat^-afk stupid robots, really reall stupid robots
23:38 zhanx Have ny read or seen it
23:38 zhanx Not
23:38 ^kat^-afk it's 1987 cheesy
23:39 zhanx My kind of movie
23:50 ^kat^-afk zhanx , speaking of ER, i found an ER11 spindle on ebay for $10.50, in all standard usa measurements (not metric), and a kit of collets for $8
23:50 zhanx Nice
23:51 ^kat^-afk [20:02] <^kat^-afk> FINALLY, a shaft measurement that makes SENSE! ; http://www.ebay.com/itm/181421830523 ; Shank diameter: 15.94mm
23:51 ^kat^-afk [20:05] <^kat^-afk> Model: ER11 (7pcs,)
23:51 ^kat^-afk [20:05] <^kat^-afk> (1/16",3/32",1/8",5/32",3/16",7/32",1/4")
23:51 ^kat^-afk [20:06] <^kat^-afk> .015mm is 0.00059inches
23:51 ^kat^-afk in case you wanted to build a minimill
23:52 ^kat^-afk ER11 tops out at 1/4 inch capacity
23:52 ^kat^-afk ER25 i think tops at 7/8, but much pricier
23:53 zhanx Bookmarked
23:54 ^kat^-afk 15.94mm = 0.62756 ,, which we all know is 0.625
23:54 ^kat^-afk or, 5/8
23:55 ^kat^-afk tried to get Tom to replace the motor shaft adapter in http://www.harborfreight.com/3-in-heavy-duty-electric-cut-off-tool-68523.html with an adapter from the ER11 shaft, so it would hold anything there's a ER11 collect for
23:56 ^kat^-afk he isn't interested, and rue poo-poo'd it