#linuxcnc Logs

Oct 07 2025

12:30 AM sinned6915869 is now known as sinned691586
01:25 AM Deejay: moin
02:21 AM lcnc-relay: <meisterdippel@> moin
04:16 AM Tom_L: morning
04:45 AM -!- #linuxcnc mode set to +v by ChanServ
04:57 AM lcnc-relay: <lucid.nonsense@> Mornin
06:42 AM JT-Cave: T-53.5
07:21 AM Tom_L: counting down already ehh
07:28 AM JT-Cave: yup
07:28 AM Tom_L: should be fun
07:31 AM JT-Cave: the weather seems to be cooperating as well
09:33 AM lcnc-relay: <lucid.nonsense@> Qualcomm just bought Arduino, doubt that's good news
09:34 AM lcnc-relay: <rs> what
09:38 AM rdtsc-w: ditto - what?
09:41 AM rdtsc-w: https://www.electronicdesign.com/technologies/embedded/article/55321526/electronic-design-qualcomms-acquires-arduino-arduino-uno-q-runs-ai-llm-code-from-inexperienced-programmer-prompts-performs-signal-processing-and-runs-linux-and-zephyr-os
10:07 AM mrec_: LLM aka GPL obfuscation machinery
10:24 AM rdtsc-w: LLMs are popping up everywhere... until they all link together and become The Matrix :P
10:38 AM lcnc-relay: <skunkworks8841@> skynet
10:45 AM lcnc-relay: <skunkworks8841@> https://www.youtube.com/watch?v=CfKX616-nsE
11:26 AM JT-Cave: very close to nap time here
11:29 AM BorgPipe: https://netpipe.ca/?p=7982 for the ultimate mancave
11:43 AM JT-Cave: https://gnipsel.com/images/wildfire-lift/wf-36.jpg
11:58 AM lcnc-relay: <lesliet@> BorgPipe: good place for the mythical "brown note"
12:01 PM xxcoder: is lift bolted down?
12:09 PM lcnc-relay: <lesliet@> I was wondering that, too
01:03 PM bdju_ is now known as bdju
01:19 PM * rdtsc-w scolds c-log for sleeping on the job
01:22 PM Tom_L: xxcoder, i don't see any bolts in the bolt holes
01:22 PM xxcoder: me either. thats why I wondered :)
01:22 PM JT-Shop: no, it's free standing and is mobile with wheels
01:22 PM xxcoder: interesting. ok
01:23 PM JT-Shop: https://www.youtube.com/watch?v=e9mRl_Q-2_I
01:23 PM Tom_L: JT-Shop, when you takin off?
01:23 PM JT-Shop: 47 hours
01:24 PM JT-Shop: thursday noonish
01:24 PM xxcoder: interesting. so its stable to lift without needing to be bolted down
01:24 PM JT-Shop: yup
01:24 PM xxcoder: and movable too. so its good for shop flexability
01:24 PM Tom_L: i'll likely be out of commission
01:25 PM JT-Shop: most 4 post lifts are not bolted down all 2 post lifts are bolted down
01:25 PM xxcoder: makes sense when I think about it
01:26 PM Tom_L: just built you a deb
01:27 PM lcnc-relay: <skunkworks8841@> this car lift suprised me..
01:27 PM lcnc-relay: <skunkworks8841@> https://www.youtube.com/watch?v=Aytf6ARcs8s
01:27 PM lcnc-relay: <skunkworks8841@> I didn't know it was a thing
01:35 PM xxcoder: yeah. good tc video also
01:50 PM lcnc-relay: <skunkworks8841@> yes - I love his videos
03:45 PM JT-Shop: https://www.tmgindustrial.com/products/tmg-alsp60-6000-lb-portable-single-post-auto-lift?variant=41858969043113&country=US&currency=USD&utm_medium=product_sync&utm_source=google&utm_content=sag_organic&utm_campaign=sag_organic
03:46 PM xxcoder: not cheap at all
03:47 PM JT-Shop: there are cheaper ones but I don't feel safe under one
04:10 PM xxcoder: hard to tell where corner cutting happened at
04:11 PM xxcoder: cheapest ones, budget paper probably was turned into a tringle
04:37 PM -!- #linuxcnc mode set to +v by ChanServ
05:05 PM Unterhaus__ is now known as Unterhausen
05:13 PM lcnc-relay: <skunkworks8841@> I don't think any of the 3d printed cases for the rpi5 work with the nvme hat we bought
05:13 PM lcnc-relay: <skunkworks8841@> It is slightly too big
05:13 PM Tom_L: if you find one print 2 :)
05:13 PM lcnc-relay: <skunkworks8841@> I will..
05:13 PM Tom_L: i mounted my nvme on the bottom
05:14 PM lcnc-relay: <skunkworks8841@> * the nvme board is slightly too big
05:14 PM lcnc-relay: <skunkworks8841@> Me too
05:14 PM Tom_L: yeah it takes the long ssd cards
05:14 PM firephoto__ is now known as firephoto_
05:14 PM Tom_L: most take the small and medium ones
05:14 PM Tom_L: ^^ technical terminoloyg
05:16 PM Tom_L: i saw a couple that take the official hat but it doesn't take the long card
05:25 PM JT-Shop: Tom_L, you getting your procedure tomorrow?
05:30 PM Tom_L: 6:30am
05:31 PM Tom_L: goin to get a steak now though
05:31 PM JT-Shop: enjoy
05:31 PM JT-Shop: rabbit food here tonight
05:31 PM Tom_L: last mean n all...
05:31 PM Tom_L: meal
05:31 PM JT-Shop: lol
05:35 PM JT-Shop: another birthday bites the dust tomorrow
05:47 PM lcnc-relay: <roguish> JT-Shop: what? ya another day older......
05:47 PM JT-Shop: yup
05:47 PM lcnc-relay: <roguish> congrats
05:48 PM JT-Shop: thanks, every one is a win
05:48 PM lcnc-relay: <roguish> a bit better than the alternative......
05:48 PM JT-Shop: yup
05:50 PM JT-Shop: almost got the passenger trailing arm assembled...
05:56 PM lcnc-relay: <skunkworks8841@> so far - it looks like maybe a 40us base thread seems stable.
05:59 PM JT-Shop: rpi5?
05:59 PM lcnc-relay: <skunkworks8841@> yes
06:00 PM lcnc-relay: <skunkworks8841@> higher than expected.. But that always seems to be the case even on pc's
06:00 PM JT-Shop: didn't Tom_L have some crazy low numbers on the rpi5?
06:01 PM lcnc-relay: <skunkworks8841@> yep - me too. but that doesn't always equate to really fast base threads.
06:01 PM lcnc-relay: <skunkworks8841@> (for mesa hardware - it is super awesome)
06:01 PM JT-Shop: ah ok
06:03 PM * JT-Shop calls it a day\
06:42 PM _unreal_: Any suggestions on what to do with a tessel 2?
06:42 PM _unreal_: I have one
06:42 PM _unreal_: linux
06:42 PM _unreal_: just trying to solve what I may do with it
06:53 PM Tom_L: JT-Shop, http://tom-itx.no-ip.biz:443/~webpage/cnc/Rpi5/Rpi5_nvme_histogram4.png
06:53 PM Tom_L: that was overnite
06:55 PM Tom_L: 40us is pretty good
06:59 PM lcnc-relay: <nein.9s@> Why is it always such a shitty experience changing oil in your car? Why have a drain bolt instead of a valve?
06:59 PM lcnc-relay: <nein.9s@> Every time I have to open that bolt, dirty carcinogenic oil gets all over my nice electric ratchet internals
07:00 PM lcnc-relay: <nein.9s@> makes the nice red lithium complex grease in there all black
07:00 PM Tom_L: and they slit the bolt so when you loosten it, half the oil runs down your arm
07:00 PM lcnc-relay: <nein.9s@> I have valves that haven't leaked in decades and this is oil so it seals well and doesn't cause rust
07:01 PM lcnc-relay: <nein.9s@> Is there something I'm missing? Or can I just replace this stupid ass bolt with a hydraulic valve?
07:01 PM lcnc-relay: <nein.9s@> I say hydraulic because those are intentionally hard to turn
07:01 PM Tom_L: it's your call
07:21 PM lcnc-relay: <skunkworks8841@> That is close to 25khz if the reset function works with the gpio driver
08:00 PM Tom_L: you gonna test it?
08:40 PM _unreal_: sooooo full
08:40 PM _unreal_: just got back from eating out
08:40 PM _unreal_: hibachi grill... SOOO full
08:56 PM roycroft: i'm having nachos tonight
09:03 PM xxcoder: just yought for me. didnt feel like cooking
09:03 PM xxcoder: might try rice tomorrow. finally found missing lid for rice cooker