#linuxcnc-devel Logs

Mar 11 2023

05:13 AM -!- #linuxcnc-devel mode set to +v by ChanServ
05:22 AM -!- #linuxcnc-devel mode set to +v by ChanServ
05:37 AM -!- #linuxcnc-devel mode set to +v by ChanServ
05:58 AM -!- #linuxcnc-devel mode set to +v by ChanServ
07:16 AM -!- #linuxcnc-devel mode set to +v by ChanServ
08:02 AM -!- #linuxcnc-devel mode set to +v by ChanServ
08:59 AM -!- #linuxcnc-devel mode set to +v by ChanServ
09:32 AM -!- #linuxcnc-devel mode set to +v by ChanServ
09:37 AM JT-Shop: pcw--home, how did you come up with (100*1747291/2333333) from MHz 2333?
09:37 AM JT-Shop: https://forum.linuxcnc.org/27-driver-boards/48369-optiplex-755?start=10
10:40 AM pcw--home: on X86 the (tmax) time is measured in CPU clocks so you need to divide by the CPU clock frequency
10:43 AM pcw--home: the 100 was for percent (I did leave out the servo period though)
10:57 AM JT-Shop: so 2333 MHz converted to Hz?
11:11 AM pcw--home: Basically 100(tmax/CPU_Speed*Servo_period)
12:07 PM linuxcnc-build: build #9793 of 0000.checkin is complete: Failure [4failed fetch branch to local git repo] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/0000.checkin/builds/9793 blamelist: Sebastian Kuzminsky <seb@highlab.com>
12:45 PM JT-Shop: thanks
01:13 PM seb_kuzminsky: pere: i need to rename hal_parport.1 to hal_parport.9 (it was initially created in the wrong manpage section)
01:13 PM seb_kuzminsky: but when i do, the .po files are all out of date and the docs fail to build
01:13 PM seb_kuzminsky: i'd like to make this change in 2.9, not master
01:13 PM seb_kuzminsky: what should i do?
01:33 PM -!- #linuxcnc-devel mode set to +v by ChanServ
01:42 PM pere: seb_kuzminsky: I would update the man page and the po4a.cfg and not update the PO files, only the POT file.
01:46 PM -!- #linuxcnc-devel mode set to +v by ChanServ
02:00 PM pere: seb_kuzminsky: note, any change to the POT file will cause conflicts when merging to master.
02:01 PM pere: seb_kuzminsky: a safer option might be to only update the man page and po4a.cfg, and leave the POT and PO files alone.
03:08 PM -!- #linuxcnc-devel mode set to +v by ChanServ
03:09 PM JT-Shop: <pcw--home> Basically 100(tmax/CPU_Speed*Servo_period)
03:09 PM JT-Shop: what units are you using for CPU_Speed and Servo_period?
03:22 PM -!- #linuxcnc-devel mode set to +v by ChanServ
03:22 PM pcw-home: hz and seconds
03:46 PM JT-Shop: thanks
09:07 PM seb_kuzminsky: pere: if i do it the safer way, would there also be something to do in master after merging this there, so the new hal_parport.9 gets the old hal_parport.1's translations?
10:05 PM -!- #linuxcnc-devel mode set to +v by cadmium.libera.chat
10:13 PM -!- #linuxcnc-devel mode set to +v by cadmium.libera.chat