#linuxcnc-devel Logs

Jan 19 2023

01:33 AM linuxcnc-build: build #6213 of 1510.rip-jessie-rtpreempt-i386 is complete: Failure [4failed configure-debian-control] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1510.rip-jessie-rtpreempt-i386/builds/6213 blamelist: Sebastian Kuzminsky <seb@highlab.com>
03:10 AM pere: so, first debian freeze is in effect now, on infrastructure.
03:39 AM linuxcnc-build: build #9626 of 0000.checkin is complete: Failure [4failed] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/0000.checkin/builds/9626 blamelist: Sebastian Kuzminsky <seb@highlab.com>
03:42 AM linuxcnc-build: build #6214 of 1510.rip-jessie-rtpreempt-i386 is complete: Failure [4failed configure-debian-control] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1510.rip-jessie-rtpreempt-i386/builds/6214 blamelist: Sebastian Kuzminsky <seb@highlab.com>, Jeff Epler <jepler@gmail.com>
04:19 AM linuxcnc-build: build #8812 of 1301.rip-precise-rtai-i386 is complete: Failure [4failed compile runtests] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1301.rip-precise-rtai-i386/builds/8812 blamelist: Sebastian Kuzminsky <seb@highlab.com>, Jeff Epler <jepler@gmail.com>
04:21 AM linuxcnc-build: build #7425 of 1401.rip-wheezy-rtai-i386 is complete: Failure [4failed compile runtests] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1401.rip-wheezy-rtai-i386/builds/7425 blamelist: Sebastian Kuzminsky <seb@highlab.com>, Jeff Epler <jepler@gmail.com>
04:21 AM linuxcnc-build: build #9627 of 0000.checkin is complete: Failure [4failed] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/0000.checkin/builds/9627 blamelist: Sebastian Kuzminsky <seb@highlab.com>, Jeff Epler <jepler@gmail.com>
04:23 AM linuxcnc-build: build #2978 of 1650.rip-buster-rtpreempt-rpi4 is complete: Failure [4failed compile] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1650.rip-buster-rtpreempt-rpi4/builds/2978 blamelist: Sebastian Kuzminsky <seb@highlab.com>
05:20 AM linuxcnc-build: build #3219 of 1640.rip-buster-rtpreempt-amd64 is complete: Failure [4failed compile runtests] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/1640.rip-buster-rtpreempt-amd64/builds/3219 blamelist: Sebastian Kuzminsky <seb@highlab.com>
05:20 AM linuxcnc-build: build #9628 of 0000.checkin is complete: Failure [4failed] Build details are at http://buildbot.linuxcnc.org/buildbot/builders/0000.checkin/builds/9628 blamelist: Sebastian Kuzminsky <seb@highlab.com>
06:58 AM linuxcnc-build2_: Build [#233](http://buildbot2.highlab.com/buildbot/#builders/13/builds/233) of `00-checkin` 4failed.
07:04 AM rmu: pere: networkmanager hast nmtui, textmode ui, that should be as bloat-free as possible
07:05 AM rmu: just FYI in case that wasn't obvious
07:13 AM pere: rmu: sure, but I got the impression that the machinists needed a GUI. :)
08:24 AM JT-Shop: real machinists don't use a gui
08:31 AM linuxcnc-build2_: Build [#234](http://buildbot2.highlab.com/buildbot/#builders/13/builds/234) of `00-checkin` 3completed successfully.
09:45 AM JT-Shop: pcw-home, did you get a chance to look for a 7i97?
10:05 AM pcw-home: Yes found a (very) bad one (encoders and analog work, all isolated outputs dead)
10:06 AM pcw-home: I'd already fixed all the production drop-outs so all I had was this RMA card in the scrap pile...
10:33 AM JT-Shop: thanks, I don't need the outputs to test that mesact works
12:06 PM sensille: JT-Shop: what do you need from those cards to test mesact? i have a small mesa-simulator that goes through identification. serving the idrom would probably be easy, too
12:06 PM sensille: a small program that listens on port 27181
12:07 PM Tom_L: probably to see what the pin list looks like
12:07 PM Tom_L: for proper formatting
12:07 PM sensille: so the idrom
12:09 PM sensille: you'd only have to make the identification and the idrom configurable, might be enough for mesact
12:55 PM pere: rmu: is nmtui missing on the live iso?
01:54 PM rmu: i don't know, it should be in package network-manager
03:30 PM JT-Shop: exactly, I need the card to load the configuration and test that all works as expected