#linuxcnc-devel Logs

Jan 19 2021

01:41 AM -!- #linuxcnc-devel mode set to +v by ChanServ
01:46 AM -!- #linuxcnc-devel mode set to +v by ChanServ
03:13 AM -!- #linuxcnc-devel mode set to +v by ChanServ
03:23 AM -!- #linuxcnc-devel mode set to +v by ChanServ
03:23 AM -!- #linuxcnc-devel mode set to +v by ChanServ
03:24 AM -!- #linuxcnc-devel mode set to +v by ChanServ
06:17 AM -!- #linuxcnc-devel mode set to +v by ChanServ
12:12 PM Roguish: good morning
12:13 PM Roguish: Is there some special reason why the 2.8 Hal document pdf is only in French???
12:14 PM Tom_L: :) woops
12:14 PM Tom_L: seems that whole set of pdfs are
12:15 PM Tom_L: or the few i clicked on anyway
12:16 PM Tom_L: so are the 2.9 set
12:17 PM Tom_L: furthere checking.. 2.7 is too
12:20 PM Roguish: Tom_L, thanks for checking. and I just realized that you are tommylight, doh
12:22 PM Roguish: Tom_L, hey, just found Mesa has the perfect little board for spindle interface.....http://store.mesanet.com/index.php?route=product/product&product_id=205&search=spin
12:22 PM Roguish: ttfn bbl
12:23 PM Tom_L: Roguish, no i am not
12:23 PM Tom_L: just a coincidence
12:24 PM Tom_L: Roguish, yes, that's the same interface i'm using on the 7i47S board
01:16 PM Roguish: Tom_L, ok, my mistaken identity.....
01:23 PM Tom_L: not the first time :)
01:40 PM Roguish: Tom_L, just ordered one of those spindle interface boards. I'll run over to mesa this afternoon and pick it up....they're only about 20 minutes away from me.
01:40 PM Roguish: and it's always fun to talk with Peter.
02:23 PM Tom_L: yeah
02:23 PM Tom_L: i used a smps for the 10v reference
02:28 PM Tom_L: 7810 would do just as well as long as the supply to it isn't too high or you'll just be heating things up
04:07 PM Roguish: Tom_L, ok, i'm a bit dense today. what's 'smps' something,something,power,supply...
04:10 PM Tom_L: switch mode power supply... a switcher
04:10 PM Tom_L: vs the 78xx series which is linear
04:21 PM Roguish: ah, gotchya
04:21 PM Roguish: Tom_L, do you use hal comp 'spindle' as in loadrt spindle.....
04:44 PM Tom_L: no
04:48 PM Tom_L: just a pwmgen component on the mesa card
05:10 PM Roguish: Tom_L, would you mind sharing your hal files?
05:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/cnc/configs/NEW_MILL_SHOP_2.8.1/
05:18 PM Tom_L: http://tom-itx.no-ip.biz:81/~webpage/cnc/configs/NEW_MILL_SHOP_2.7/
05:19 PM Tom_L: they're both the same save some 2.8 update changes
05:19 PM Tom_L: and some commented code that should be removed
05:37 PM Roguish: THANKS A MILLION.....
05:38 PM Tom_L: np
05:42 PM Tom_L: ignore some of those files
05:42 PM Tom_L: just in case backups :)
06:54 PM Centurion-Dan2 is now known as Centurion_Dan
07:41 PM Centurion-Dan2 is now known as Centurion_Dan